Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
hello there i think i need two uart in my application. i read datasheet of both nrf51 and nrf52
in both there is only one uart.
can anyone have implemented software uart...
Use this routine E:\nordic\nRF5_SDK_12.2.0_f012efa3\examples\proprietary_rf\gzll\experimental\gzp_desktop_emulator
To modify the can communicate with PC nrf24luep pairing...
Hi.
I'm troubled.
I use nRF52 preview DK v0.9.0 & Keil5.
i tried ble_app_hrs_c in example folder of nRF52_SDK.
This program stopped at
err_code = sd_softdevice_enable...
Hello all,
I am actually implementing an SPI-master driver in non blocking mode, I write the following code, when I use a debeug led, the program enters well in the IRQ...
I started with the blu_app_template on a 52840. I have advertising working. I can see that from an iOS app. I can also see the details of the service. I see the characteristic...
I am using the Master Emulator C# examples to build my own application. None of the examples are able to properly connect to a remote device. When I open up the Master Control...
I'm writing an nRF52 DK btle application using SDK 12. The DK comunicates with 2 external peripheral via SPI and I2C interfaces. Complilation fails with the error:
._build...
hi, i am reading mpu6050 with nrf51822. every now and then the data got corrupt because of softDevice interrupts. if i don't use Softdevice the it runs perfectly but when...
Hi All,
I am using UART with baud rate 4800, with even parity and 1 stop bit. I'm getting 6-8 bytes in a packet. I'm receiving packets for every 8-10ms continuously. This...
I am attempting to use Unity + CMock onboard the nrf51 for unit testing. I have Unity working and can even output the results of unit tests using Segger RTT libraries. There...
When I try to install nrf5X command line tools in Windows 10, I get the error mentioned in the title, even though I am not doing installing any software in parallel.
Error...
I am attempting to use TIMER4 on an nRF53832 using SDK 12.2.0 but I seem to be running into some sort of granularity issue.
Specifically, if set up the timer with 16MHz...
I just received my new NRF52480 PDK, but it will not respond to any commands.
I tried nrfjprog -e -f nrf52 and this is the log output:
-----------------------------...
Working with nRF52832 and SD132-v2.0.1
Using external 32.768kHz xtal in addition to 32MHz xtal.
I realize there are a lot of posts about timers, but I didn't find any...
I'm having difficulties writing, retrieving and deleting data from flash, using fds on nRF52832_XXAA. Sometimes the flash writing succeeds, sometimes it fails with with ret_code_t...
