Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hello dear Engineers!
the questions are should I connect pins DEC2:A18 and DEC2:E24 externally ?
shuold I use Capacitors to decouple both these pins (in Reference no...
Dear developers,
we are considering purchase of a reliable programmer capable to flash the nRF51822 in production, one possible option is the SEGEGR FLASHER PORTABLE or...
Hi!
I have noticed strange problem with one of GPIOs - P0.15. We have tested 50 devices based on nRF52832 and 3 of them have problem with P0.15 after few days.
P0.15...
The default I2C address of my sensor is 0x29 (7-bit).
If the least significant bit is low (0x52) the message is a master write to the slave. If the lsb is set (0x53) then...
I'm using SDK 12.2.0 with softdevice S130 V2.0.1 and want to use TWI.
Using the ble_beacon example I added the twi code from twi_sensor.
Shortly after calling TWI_Init(...
Hi,
during normal operation, my device shows a power consumption of 4.7mA.
Normal operation is:
accelerometer (lis2dh) detects a shake and wakes up the nrf51 via...
Hii ,
i am using customized board (chip : BT832).
err_code = sd_softdevice_enable(clock_source, softdevice_assertion_handler); hangs. it took some delay and after that...
Hi all,
I have seen a pair of questions ( this and this ) that I think have something to do with this, but didn't find a solution.
I have a custom board with a button...
I want to have an application similar to UART in the SDK example, with multiple peripherals.
I tried to modified existing UART example, but cannot make the central node...
I want to add the nrf52832 to my customized board and I am studing the possibilities for flashing it once that is located on the board. Is it possible to flash trhough the...
I have a board with some LEDs that are driven in the same way as with the nRF51 DK board (i.e. there is a resistor in series with the LED and you drive the pin low to turn...
In our testing we encounter some devices (Centrals with nrf52832), where the peer manager event PM_EVT_BONDED_PEER_CONNECTED contains a invalid peer id 0x4000 (allowed values...
I have a device the uses MSP430f169 and CC2500 RF controller for communication I need to replace the CC2500 RF controller with nRF51422 device.
As I understand an nRF51422...
Hi,
I develop application on MBED platform with NRF52-DK. I figure out that pin "logic" on this board is interchanged. For example. I have LED connected to some pin. When...
Hello,
on my custom board I am trying to use pin P0.09 and P0.010 for interrupt-purposes. So I integrated the necessary adjustments as mentioned in this topic here , which...
