Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
I just got my NRF51822-BEACON. I didn't see any LED flashing when I insert the battery. Also I can't find this beacon on nRF Beacon android Application.
hi,
i need to do long process and more flow of functionality that all could stopped by softdevice. so i need to enable and disable soft device. could it could affect my timer2...
hi
here i have use block size 16 byte and block count 5096. this is my start address 0x27000
i have tried to clear 79 pages.
and read data from flash with specific...
Hello to all
I have the next code, basically what it does is reading a button state and if it is pressed then the manufacturer data of the BLE package is lets say B, on...
Hi All,
I would like to know what the default value is for the radio TX power for the nRF5240. According to Nordic's specification, the output power is programmable from...
In the ULP Wireless Q magazine (edition winter 2016), on page 12 / 13 there is listed that the nRF52 chips have a Battery Monitor peripheral but I cannot find anything about...
I have been developing my application using gcc on an NRF52 by putting the text section at 0. This was convenient to get going quickly. We initially weren't going to launch...
hello, i am doing flash read and write in nrf51.for which i have used the C:\nRF5_SDK_12.2.0_f012efa\examples\peripheral\flashwrite\pca10028\blank\arm4 this exampl.
but while...
Hi,
Could somebody share the schematic and board files of nrf51 beacon?
We are planning to make some changes. I don't intend to buy a beacon because I have already purchased...
Hi,
I use the bootloader in the SDK V13.0, I found that no timeout as the SDK v12.x. However, I have added the WDT to the bootloader refer to the link link text
it still...
i could not run timer2 with soft device,. if i start initiaize TIMER2 the bluetooth advertise has disabled. i need this timer to timeout my flow function. i think softdevice...
Hi,
I used the hrs example found some problems, the problem is described as follows:
I use the Android phone pairing binding device, when I cancel the pairing on the phone...
hello,
What is the difference between the next two events?
On_ble_evt ()
BLE_GAP_EVT_TIMEOUT == 0x1 B
On_adv_evt ()
BLE_ADV_EVT_IDLE
I can not understand well.
With...
Hi;
I do not know the BLE Event(DFU bootLoader/SDK Sample) so I will ask you a question.
The environment using is below.
SDK v10.0.0 (Sample code/dfu_transport_ble...
