I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'm trying to buy more data for my iBasis SIM cards that are provided with the nRF9160. I have 4 registered SIM cards and it was easy to buy more data through iBasis in the...
Hi,
I want BLE and ZIGBEE to be able to switch dynamically during running.Only one mode(BLE or ZIGBEE) is running at a time.If switching from zigbee to BLE, how do I turn...
I have implemented DFU functionality in my Bluetooth mesh project and used device A as the distributor and device B as the node to be updated. I have already configured both...
We have our firmware developed with ncs2.7.0 and everything works as expected. However, with a recent effort of moving to ncs2.9.1, the same project can be built but during...
When calling the bt_conn_le_create_synced function to create a connection to a peripheral, which is synced to the PAwR train, I get a CONNECTION FAILED TO BE ESTABLISHED ...
I have a BMD 350 nrf52832 module connected to nrf52DK board via P20 header. I am using nrf52DK to flash the firmware onto BMD350. my code works with nrf52DK and it logs onto...
We are trying to increase the TX output power on the nRF5340 when using Enhanced ShockBurst (ESB) . According to the product specification, the nRF5340 supports +3 dBm TX...
I am receiving packets in monitor mode on a nRF7002DK. I need some advice on how to interpret the signal value. From <modules/nrf_wifi/fw_if/umac_if/inc/system/fmac_structs...
Hello
I'm currently working on writing some specifications for a future product. In this product, I want to use the advertising mechanism to send specific data from one...
Hello,
I recently acquired a Thingy91 board in order to make a hardware prototype. I already have experience developing with the nRF52840 so I took inspiration from my working...
we don't seem to have power numbers for the 54L, but in the 5340 datasheet it shows the LFXO (0.16uA) used less power then the LFRC (1 uA).
Is that true with the NRF54L...
Hello, I am working on a project using a custom hardware configuration based on nRF5340 and nRF7002 similar in configuration to the nRF7002-DK, except without the on-board...
Hi!
We're building a project for the nRF54 where we want to run an external library on the FLPR core.
Right now we have a prototype PCB with a module from Fanstel on it...
Hi,
Is it possible to make the MQTT connected device receive the Shadow config updates and AT Commands immediately? Based from our testing, the device only receives the...
Hello,
I am using configUSE_TICKLESS_IDLE with RTC2 setup for FreeRTOS tick, occasionally I am seeing the asserting in task.c at line configASSERT( ( xTickCount + xTicksToJump...
