Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
A new library/toolkit has been built that allows us to invoke the services of an nRF24L01 from a Java environment. Documentation and links to the Github project can be found...
Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
Hi,
I am attempting to get Direct Test Mode working on my nRF54L15 while also having access to the normal BT stack.
Normally, if I run dtm_tr_init(), I can begin the test...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi,
I am testing the Bluetooth function on my custom board with nRF5340 CLAA chip. I have tested the clock, I2S and SPI on this chip previously and they all worked perfectly...
Hi everyone,
We're reading BAT level by reading data from ADC pin and the setup diagram is shown below.
We tested our device at hospital, and we observed significant...
I am trying to populate a nrf_twi_mngr_transfer_t at runtime depending on chunks of an input file that I'm pushing to i2c.
nrf_twi_mngr_transfer_t const write_cfg_transfers...
Hello,
I am trying to connect to the PPK2, but I see on device manager stating that the PPK2 needs drivers to be installed. I have nRF connect v5.2.0. I have tried uninstalling...
We are currently working on a project based on Enhanced ShockBurst (ESB) and would like to use Front-End Module (FEM) support with the nRF21540.
In your Enhanced ShockBurst...
Morning, I was trying to access https://academy.nordicsemi.com/ but the browser responded with an error `Domain configuration pending` and showed `Kinsta` node is down. Any...
Hi Support Team
We follow the guidance of the following link to program firmware to external SPI Flash of nRF54L15,but it failed.
https://docs.nordicsemi.com/bundle/nrfutil...
Hi,
I am desperate with creating my own board. I followed the example of nrf54l15dk, but I absolutely do not understand why I cannot build - not even assembling Zephyr....
Hello,
I am working on custom hardware that is based on the nRF7002 DK. The following parts are presently listed as either EOL or NRND in distribution. L6, L8: Taiyo Yuden...
I am trying to connect some I2C sensors to the the nrf9151dk and I cannot figure it out. Where do I physically plug the sensor into the board and what configuration setting...
We have been evaluating the nRF5340 and nRF7002 for use in a new product and we are currently looking at our Wi-Fi FOTA options. For reference, we are using an nRF7002 DK...
Hi Nordic team,
We are developing two types of devices based on the Zephyr examples:
periodic_adv_rsp
periodic_sync_rsp
Our design uses the following...
Hello,
Hopefully this will be a quick(ish) one since I think I found the answer, but just need confirmation.
To preface (My setup):
nRF9151DK
Modem firmware: mfw_nrf91x1_2...
