Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi,
One of my pca10040 stays on bootloader mode.
I have tryed copying J-Link OB-SAM3U128-V2-NordicSemi 160212.bin file on the bootloader drive but it stays the same. ...
Hi Everyone,
I just purchased an nRF52840 PDK and I am trying to program it via nRFgo. I erased the flash, selected the latest s140_nrf52840_5.0.0-3.alpha_softdevice.hex...
Hello,
My team and I are experiencing a problem with our custom DFU Bootloader, which is based on the Experimental Bootloader Secure Serial example (SDK 13), running in...
Hi,
My SDK version is 13.0 and my problem is when I run the examples\ble_peripheral\experimental_ble_app_buttonless_dfu project the 52DK seems ok but when I use the DFU in...
Hello:
I am setting up my nRF52840 development board to work with the S140 softdevice on Segger Embedded Studio; however, I am running into issues with the flash_placement...
Hello,
I've seen some conversations around the forum for applications that must share the same ID. My application must share SPIMO and TWIMO (ID 3, base addresss 0x40003000...
Hello,
I want to make beacon with my uuids. I am referring to code ble_app_beacon code from sdk 12.2.2
I have made changes according to my requirements in my code.
I am...
Hi, we downloaded the latest version of the sniffer 1.0.1 (today).
We tried that but we could not get it to work reliably?
The application sees the device, we select and...
I am using the nrf51822 with a latching circuit as shown controlled by P0.05 pin.
I am using the following code SDK 10.0 S110 softdevice to Power ON the circuit (PowerPin...
I've merged serial dfu with ble dfu project refering to this post .
I'm getting linker errors stating no space in execution region in .ANY sector...
What could be the...
Hi,
I have add beacon function to "light_control_server" project. I want to every server broadcast their unicast address.
Could do kindly teach me how to do this. It's...
I am working on a project with a nRF51822 on a custom PCB. The application is based on the ble_app_template-project from SDK 10.0.0 and I am using S110.
Now I want to measure...
I've just tried upgrading to 5.2.0 from 5.1.0. I simply downloaded the new SDK's zip file, extracted it next to the old one, and adjusted my makefile to reflect the new path...
