Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
Hi,
I have a device with nRF52832 and firmware is composed of Bootloader (BL), softdevice (SD) S132 v2.0.0, application and I am using SDK 11.0.
I have created different...
Currently, we are trying to have the nRF51 chip working with a type of capacitive pressure sensor. We did quite a lot of work on searching proper circuits of reading the capacitance...
I have 2 board nrf52840 DK, I now I want to send file ( 1~2 Mbyte) from board_1 to board_2 without use UART. where can I get example to do that ?
PS: I also need example...
I've merged the experimental_ble_queued writes sample code into my project and am testing the long write characteristic with nrfConnect from an Android phone. I get no errors...
Hi,
I am trying to figure out the reboot reason on an NRF52 in order to solve it in the best way.
We have a design with a dual supply 3.6V/5V going through a 3V LDO...
Hello,
i have a BLE Peripheral that has a service that we use to simulate UART over BLE. Very similar to the nRF UART. I consider the time to establish a link that allows...
Hi all,
I am trying to save an UART variable I am receiving. My case is very similar to the example Flash Write Example, but I would write few bytes instead of the whole...
Hello!
I have to sample audio signal from a microphone (MAX 9814 adafruit) with the nrf52 board. I use the saadc and then I perform a FFT of the data using the sdk 13 examples...
I implemented my profile based on GLS example. my profile has five services and every services have several characteristics. Pairing with several smartphone work properly...
hi,
I would like to use pwm to output the 1HZ waveform to drive the motor, but when I set the frequency to be 1HZ, I can not find the device and cause 51822 to reset.
This...
Hello, I'm working with the NRF6310 Motherboard and play with it a little with SDK 6.1, but i want to create profiles with the Bluetooth Developer Studio, so I started using...
I download "nRF5_AirFuel_SDK_2.2.0_7b89a57" and use "ptu_app_beacon" development, I am currently using "nrf51822-QFAA" and "nrf51822-QFAC", how do I set up IROM and IRAM?
Hello iam using softdevice 110 and SDK 10.0.0, Iam trying set tx power of nrf51822 using function sd_ble_tx_power_set(), i have tried 0dBm and 4dBm both are giving same RSSI...
wqewqeqwe.PNG I want to program the nrf52 chip using J link Edu -SWD mode. I actually connected the SWDCLK, SDI, and Vtref and GND of Jlink EDU programer to SWDCLK,SDI,3.3V&...
