I am working on project using thenRF9151 board and I require the GNSS functionality to work for the same. However, my board is not able to latch on to a satellite network...
i have PMIC(I2C based )Max20360 that is developed using twi sensor , to this when i am intergrating a SAADC part throws error error # 134 :expected a field name . 1)why am...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello,
I’m having an issue with my setup: I have a nRF9160 running the bt/peripheral sample through a nRF52840 (running the hci_lpuart sample). It seems to work fine with...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Please excuse my ignorance, My company is designing in the nRF52832 for our first product using both ANT and BLE. From looking at the documentation on thisisant.com there...
I've got a strange problem with updating my Magnet-Characteristic.
I use a service with 4 characteristics (Gyro, Acc, Mag and Temp Values) and update them on a timer base...
Hello,
Two issues want to ask, after tried the BLE_NUS example code.
From other posts, still does not exist clear solution (example, pictures) ?
Sure has an application...
Hello,
I am working with the uart module. While configuring the uart I encounter 2 issues.
First when in the uart_init function the pin for uart output is configured...
Hi,
I am using nrf51822(128k), SD 6.0, SDK 5.2.
I found that nrf uart v2.0 app will add a "0x0A" at the end of data that I want to send.
How can I remove this?
Thank...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
I've never used Gnu's GCC before, but after 20 hours of trying and failing to install it on my macbook, I'm finding a shining hatred. I've downloaded their exhaustive list...
I migrated to nrf52 and countering some problems.
I am trying to sample 4 pins every 2ms with SAADC.
I started with Example here .
I simply changed
uint32_t ticks...
I've got a gyro I want to read some data from, but I don't know the values and can't verify if they got read correctly. When does nrf_drv_spi_transfer start to read?
i...
Hi, i;m trying to build the "nrf52-ble-app-lbs" example which i downloaded from git hub github.com/NordicSemiconducto....
I followed the instructions in the README file...
I'm thinking about changing ADC resolution during operation.
What I want to do is:
start
・Operate in 8bit ADC(normal time)
↓
・Operate in 10bit ADC(particular...
I want to use NRF51 DK to sample 2 analog signal continuously (300Hz) and send it to a smartphone using BLE.
I need advice on
Which nrf example to use to code my DK...
I've run out of space in my attribute table. No problem, I'll just make it bigger with ble_enable_params.gatts_enable_params.attr_tab_size .
The easiest way to do this...
