I was implementing custom services and characteristics(softdevice:s140, ble) on the nrf52840 dongle, however I couldn't get it to work, even though my code seemed correct...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Hi,
I use s110_6.0.0 and sdk_5.2.1 in my old product. I found that I can't write flash sometimes. Timer1 and Timer2 are used, and their interrupt priority level is 1(high_priority...
Hello,
I noticed that their was a question in the developer zone regarding MD bit?
devzone.nordicsemi.com/.../
My question is slightly different. I am using Soft...
Is it possible to use random 128-bit UUIDs for custom services and characteristics? Or do the characteristics in a service need to share 96-bits with the custom service UUID...
The hardware bug #39 on the GPIOTE in EVENT mode which gives a overconsumption of ~1mA even in idle mode on, kills the interest of having a low power chip, because the solution...
I am wondering, for 51422 or 51822, are all radios can work simultaneously or only one type of radio can work at a particular time?
e.g., BLE & ANT can work at the same...
Hi all,
Is it possible to get a callback from the softdevice, when a characteristic is changed? If so can you guide me in the right direction - documentation / examples...
@brief Function for application main entry.
*/
int main(void)
{
// Configure LED-pins as outputs.
LEDS_CONFIGURE(LEDS_MASK);
// Toggle LEDs.
while (true)
{
for...
Hi,
I'm using gazell library with app_pwm.
From documentation gazell use Timer2 and PPI channels 0,1,2.
APP_PWM use Timer0.
When I disable pwm using app_pwm_disable...
Hi,
I'm trying to use the nRF52832DK to flash a Rigado BMD-300 module (nRF52) - I've connected SWDIO, SWCLK, GND and voltage sense to P20.
It seems that because the...
I run the boardcast tx application on a nRF52832 board and I add uart drive into the proj. I use UART to console on PC.But uart doesn't work, PC console nothing. What's wrong...
I'm using the mouse example which use bonding and white list which allow to connect only to one central after performing the bonding
my question is, does the bonding feature...
Hello,
Is this the correct setup? What else will I need to do to make it work (e.g. it says something about the MCU will detect the external board and then programm/debug...
I want my device to pair only with a single central device at a time. So once it gets paired, it should not be able to pair with any other device. For this purpose I use directed...
Hi community,
I'm studying the possibility to be able to link multiple central devices to one peripheral. As it defined in the s130 soft device description ( www.nordicsemi...
I upgraded Arduino IDE to 1.6.8 version, it was automatically set up Programmer AVRISP mkll, in previous version I can see that was Atmel STK500 development board
in Tool...
