Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hello,
I’m trying to run the TensorFlow Lite Micro example (zephyr_samples/hello_world) on my nRF5340DK using nRF Connect SDK 2.6.1, but I’m unable to build the project...
hi support team,
when i testing wifi location, i found out one problem:
nrf_cloud_rest: Failed to encode location request, err: -12
that is this code in nrf_cloud_rest...
We need to set a GPIO pin in MCUBoot to activate an external USB hub chip so the USB DFU will work. I would like to do this with code in our project rather than directly modifying...
Hello,
I’m working on a Zephyr-based application using the nRF5340 where I need to optimize power consumption. The intended behavior is:
The device should stay in...
According to the nRF52832 Product Specification, “A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply range, may...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-3-dfu-with-external-flash/
I have this exercise...
Hello ,
We are working to an OEM Security System project that is using BLE.
The system contains at least 2 modules that communicate using the BLE technology.
One of...
I am trying to run the example ble_app_hrs on the nRF51 dk PCA10028. I target and build the file, and I believe it makes it onto the device, as the old program on the device...
Hi,
when i program my eval kit using nRFgo studio, the chip dosen't work unless i do a hard reset OR put off supply and put on again.
Any idea ? My program, is dfu bootloader...
Hello Nordic Team,
I am sorry to say this, our development team found a major glitch in micro-esb communication protocol. we are in stage of pre-production of medical sensors...
Hi
We are thinking of using NRF51 for BLE and CPU capabilities. But we also need a Wifi add-on to connect to cloud.
What is the right chipset for this? Which ones are...
I have a demo(s110) set up with some custom services, and in them custom characteristics. The services each relate to a specific sensor element on my device, so have a mostly...
I'm using ble_nus_string_send() to send 15 bytes over BLE UART.
As expected it sends 15 bytes, however on occasion 14 bytes are sent instead of 15 bytes.
Would there...
I ordered nrf8002 IC. I am using following breakout board PCB & not using Nordic development kit.
www.proto-advantage.com/.../product_info.php
I gave 3.3V to both VDD...
I've been working through the tutorials on BLE Services & Characteristics. That's all gone fine for me. Now I'm adjusting the sample code to use different UUIDs for my own...
Dear Sir.
I have a question for app timer in nRF52 DK(pca10040).
I was called a example source(ble_app_hts) for nRF5_SDK_11.0.0-2.alpha.
And I add UART part for logview...
Dear All,
I have question regarding advertising in NRF51. I measured the power that be used when advertising using osciloscope and set the advertising interval of NRF51...
I'm having this event and I'm not sure what are the conditions required to trigger it, also what does it mean exactly since the documentation does not say more than a line...
I had attended the Nordic 2015 Tech tour in Helsinki and it was very nice of Nordic to give away nRF52 DK to all attendees. So far, I've been busy working with nrf51 but today...
I follow this instruction to turn Raspberry Pi into an IPV6 router on IPV4. My raspberry pi works well after I add nameserver to /etc/resolv.conf.
But other device in my...
