Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Dear Sir/Madam,
I want to use the One channel of Timer 1 for PWM generation and other channel is used to measure the pulse width of input square wave.
For above i need...
When I try to step through my code, I get a wdt event firing. I have tried setting the behaviour to pause during debug and sleep
void wdt_init(void)
{
uint32_t operationStatus...
I would like to measure BER and PER on custom board by using sample project that is included SDK.
\examples\dtm\direct_test_mode\pca10028\s110
Could you please teach...
Hello,
I'm powering a Readbear BLE nano using a CR2450 coin cell battery. The firmware application is written using mbed. How can I measure the battery level of the CR2450...
hi,
can i use timer interrupt has more than 1ms period??
#define APP_TIMER_TICKS(MS, PRESCALER)
((uint32_t)ROUNDED_DIV((MS) * (uint64_t)APP_TIMER_CLOCK_FREQ, ((PRESCALER...
Hi, I'm trying IOT SDK now and I got some questions
My devices: nRF51422 DK, nRF51_iot_sdk_0.8.0_f1f6187, iot_ipv6_coap_client_pca10028
Q1: Why is the advertising interval...
Hi Nordic support,
I am building the ble_connectivity project of the latest SDK11. My EVB is pca10028m, the project is located under "nRF5_SDK_11.0.0_89a8197\examples\ble_central_and_peripheral...
HI,ALL,
in the Blue Core Spec, there are such statement here,
L2CAP permits higher level protocols and applications to transmit and receive
upper layer data packets...
Hi, I use [nRF5_SDK_11.0.0\examples\ble_peripheral\ble_app_hrs\pca10040\s132],but I get error such as the following.
{
............\components\softdevice\s132\headers...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
HI, I am new to embedded system and just start to learn NRF52 DK. currently I want to configure a pin of nrf52 as interrupt. so i created new GPIOTE_Handler function . however...
hi, i am getting a lot of help in here, thanks a lot
i'm using SDK 6.0.0 for my project. and i want to use timer as a counter like as the title.
then, i fount the app_timer_cnt_get...
hello,
I am using S130 softdevice. While I am trying to connect with MCP I am getting one error with error code :0x08. and MCP is showing a message like "Lost connection...
Hi,
I have a battery powered device which goes to system off mode when it is not used. I want to do some stuff when the battery is inserted the very first time after production...
