I was doing development on the development kit and I noticed that when flashing the device there is application core and modem core firmware that is flashed
I'm trying to...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
We have a nrf51822 chip connected to an arduino-like device. We need to use UART for communication, but without firmware modification the master chip doesn't support USART...
Hi.
I'm using PCA10028, SDK10.0.0, S130. I'm a beginner.
If I want to download hex files(soft device and fw code) though UART port, is it possible?
If possible, could you...
Dear all,
I checked the SDK release note and found Nordic decide not to support CMSIS anymore.
As I developing with 52832, I try to use FreeRtos to control the whole system...
Hi: I want use freeRTOS on nrf51822 based on sdk10. But when I open the example project"blinky_freertos"and try to use it, The keil5 manage run-time environment tell me "install...
I am developing a BLE peripheral with SDK9 and SD110. The PPCP are 80-400ms, 5 slave latency and 5s supervision timeout.
I am currently running some blocking code in response...
I'm having trouble with my call to ble_advertising_init when using S130 soft device v2.0.0 on an 10031 device with SDK 11.0.0, I'm getting error_code 7.
When I try and...
Hello everybody,
Does the S312 v2.0.0 handle BT operations completely independent for each BT connection? Can I read/write from/to different characteristics on different...
Hi!
I am studying some program code of BLE examples.
I have a doubt about what does the evt_handler() do.
E.g.
in the example "ble_app_hrs_s130_pca10028"
static void...
We are treadmill developers and we want to include bluetooth capability to our products.
We found, on the bluetooth website the RSC characteristic ( Running Speed and...
When switching to nRF52_SDK_11, the compiler does not find core_cm4.h which is found in components/toolchain/CMSIS/Include.
I get this when compiling
nRF5_SDK_11.0.0_89a8197...
I am trying to program a custom board connected via the DK. The custom board is 16KB version (nRF51822 QFAA). RTT consumes lot of memory and hence my code does not compile...
I am using nRF51422xAC SOC.
It is advertising perfectly and able to catch that with sniffer module. But unable to find the same device on any mobile phone. I've tried with...
Can i use the nRF Toolbox app as a BLE peripheral and the nRF51-dk[PCA10028] as a central device.
Also,if not,then please suggest any other App that can be used for the same...
Hello,
I've downloaded nRF5_SDK_v11.x.x and install it, my keil version is v5.14. I flashed s130 v2.0.0 into nrf51DK, then build "ble_app_beacon" basing on SDK v11.0.0 and...
