We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
I have designed a custom PCB with Nrf52 for an ECG wearable sensor application and is trying to optimise the power consumption of the device. The application is to collect...
Hi.
I'm currently trying to scan beacons with timeslot example.
However, I found that there're more than 20% of loss while scanning beacons broadcast.
I think that...
Hi, I tried Adding another service to the LBS Program, but the chip is getting reset , i have another 16 bit uuid service with different base uuid, Its getting stuck at SOFTDEVICE_HANDLER_INIT...
hi
im using nrf51422 v2 with external sdk v6 with softdevice v7
im running one of example that its name is ble_app_template and when i run it , it show up for just one phone...
hello,
I want to change the advertise time out time by BLE_GAP_ADV_TIMEOUT_LIMITED_MAX.
Is there a problem with changing BLE_GAP_ADV_TIMEOUT_LIMITED_MAX to ex. 1000sec...
Hi,
I can use nRFgo Studio via nRF5x Bootloader to update application firmware(Hex file).
It look to be using "nrfutil.exe" to create a XXX.zip file and go through UART...
Hi.
I am on nRF52 DK (PCA10040 v0.9.0, s132 SD), SDK 0.9.2 and Linux (Ubuntu).
I am currently working on the SDK's example ble_app_uart.
I am only using gcc, and...
I was working with examples/ble_peripheral/ble_app_gls. In the SDK11alpha configuration, I paired the dev board with my Android phone running nRF Toolbox and was able to start...
Hi,
I loaded S110 v8 to nrf51. Then I loaded dfu_dual_bank_ble_s110_pca10028 bootloader.
With this setup, I'm able to download my application via the bootloader.
The...
Hi,
Reading the nRF52 product specification, I see:
"If the antenna is exposed to a strong NFC field, current may flow in the opposite direction on the supply due to...
Req: from the cap-sense board, different tap will be done by user (like 2 times tap, 3 three times tap etc). so the Bluetooth board (nrf52) will receive these taps as interrupt...
Hello Devzone fellows :)
As you may notice, we have posted our first webcast: Interfacing with Nordic's Softdevices .
It's the first test run in a series in which we...
Anyone knows which Nordic chips they have used in this device, and do you know if it is possible to get it to Arduinio?
www.tu.no/.../345999
http://sfty.com/#produc...
Hello,
Some little compilation errors.
in ble_radio_notification.h
typedef uint8_t nrf_radio_notification_distance_t; => is no more defined in SDK but used here
...
