Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
I used AdaFruit Bluetooth LE shield previously that uses nRF8001. I can define new customer service using nRFgo studio (which only supports nRF8001). I am moving towards using...
Hi,
I am using pca10040 board. i need to toggle a led in 5sec once. I tried to change the prescale value. But im not able to get that much time delay.
Can any one help...
SDK Version: nrf51_iot_sdk_0.8.0_f1f6187
In SDK all examples are given for PCA10028. Is it possible to run on PCA10001?
What I have done so far with PCA10001:
1.Programmed...
Hello,
I have modified the Android-nRF-Blinky Application to use it with the Datathroughput Demo on the nRF52 DK.
The android application runs on a Nexus 9 with android...
Hi, i try to understand how to use mode for supply voltage measurement. But i have a problem and i get always 1.225 volt
hal_adc_set_input_channel(HAL_INP_VDD2_3);
hal_adc_set_reference...
Hey all,
Wondering if we could use an external 65.536KHz LF clock, or thereabouts, instead of the 32.768KHz? We need better resolution for the RTC, but don't want to turn...
hello im from mexico, last week i order 10 NRF24LE1 and arrived the next wake,
but before i have many cuestion about.
someone can tell me that the burner can work?
compiler...
I had a mbed firmware running on a ST Nucleo 64 that periodically query a sensor for data. It only use the I2C, a button interrupt and a LED for heartbeat. I ported it to...
Hi,
I want to know that if the TWI easyDMA in nRF52 can help in achieving this task:
we want to read from TWI each 10msec based on a timer interrupt and write...
Hello:
I have detected a problem with a timer on my program.
I can solve it, but I would like to understand what is happening exactly.
My program starts to scan BLE signal...
I'm writing the client-side code for the Nordic DFU service and according to the spec, the DFU packet characteristic uses Write Without Request. Are there any examples of...
Hi,
I'm trying to implement a HID gamepad on nRF52832. Here is my situation:
nRF is receiving frame over UART from master uC every 15 ms. Frame is being converted and...
I was trying to track down high, approx. 6mA, processor current consumption and I have found high current consumption if the FPU executes a divide by 0. If I comment out the...
