Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hello All,
Sometimes is fine to use a forum but sometimes we have to meet a deadline and the forum questions don't always get answers for in a timely manner.
So I'm...
I would like to use Channel 0 of the S310 Stack V1.0.0 on the nRF51422 to do a background scan of ANT devices.
I am testing against ANTWARE II v4.1 with the ANT+ usb dongle...
Hi,
I'm working on the ble devices to transmit sensor data using s110 and s120 with one connection.
I want to send 6 packets for every 7.5 ms connection interval from the...
I have been to a number of Nordic events this summer, and it was hinted / suggested / unofficially announced that there would be a third SKU of the nRF51822, that included...
Hello,
I am creating a PCB design for NRF2402AG but I'm not sure whether I should connect pad under the NRF to the ground or I should left them isolated. I could not found...
Hello
I get this error when I try to program the module:
Parsing hex file(s).
ERROR: Cannot find C:\Nordic Semiconductor\nRF51 SDK_v6.0.0.43681\Nordic\nrf51822\Board...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
Hi dear friends from Nordic Semi,
I´m in great trouble trying to make these nRF24L01+ to work, one unit as a transmiter, and one unit as a receiver, it can be to send 3 bytes...
Hi,
I am using nRF51822 Evaluation Kit along with keil uvision4. Will using optimization in keil IDE make any problem in the normal working of BLE project? Will it affect...
Hello All,
We need to design a Remote Control based on NRF24LE1 working with mercury cell.
So they key factor is hardware & software optimisation for the lowest possible...
Is anyone aware of any of these on the market yet? I know of one, from Insight SIP, but am keen to hear about any others.
(This would save space on the PCB, simplify our...
Using twi_sw_master have discovered that the nrf51422 E00 draws 1.3mA in off mode.
When the twi device is removed from the bus, the nrf51422 draws under 5uA in off mode...
I want to merge soft device, application and boot loader in order to improve efficiency for factory. I searched relative topics in this forum and found something useful. At...
We have been unable to establish a link between a Garmin HR monitor over the air, we have established USB comms to a cell phone device. We took the transmission line directly...
i find one related question:
devzone.nordicsemi.com/.../
and this is refers to nrf8001,
so, i wonder if nRF51 could share both crystal with other MCU?
please help to...
