Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Bluetooth physical layer Direct Test Mode testing is used to verify BLE low-level RF transceiver performance. The required software is nRF Connect for Desktop V3.7 + Direct...
Hi,
When starting nRF Connect for VS Code, SDK v3.3.0, the message Unable to resolve configuration with compilerPath: "C:\ncs\toolchains\fd21892d0f\opt\zephyr-sdk\arm-zephyr...
Hi,
We have two option to use Flash memory,
Option 1: We are planning to use Flash Memory on the SPI bus shared with the NRF7002. Kindly confirm whether this configuration...
Hello Nordic Team,
We are trying to test an I2S DAC (MAX98357A) with the nRF54LM20B EVK . Could you confirm if this is supported and which sample application is recommended...
Hi,
I’m working on the T5838 Invensense PDM driver for the nRF54L15 .
I’m referencing this driver: IRNAS T5838 Driver , and have updated it to work for SDK 3.0.2 (including...
Hi Nordic teams,
I am working on integrating single-slot DFU for the nRF54H20 based on the throughput example. However, I noticed a difference in how the Bluetooth controller...
Hello,
We developped a new rf board with 54l15 µc.
We discovered our UART communication have some errors with -16 °. At -20 ° the device doesn't respond.
I changed...
Hi，
Hello, I frequently need to perform BLE DTM testing, but there is only one CWM500 instrument available, and I have to queue up and wait for it every time I run tests...
hello Nordic
we are working with nrf52840/nrf52832 with ncs (currently on v3.0.2)
i have noticed that when i try to dfu a merged artifact of my version with the new mcuboot...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
Hi, we want to evaluate the BLE ISP2454-LX chip.
To do this we bought from RUTRONIK FRANCE an ISP2454-LX-EB evaluation board with the ISP2454-LX-TB test board.
SDK : nRF...
Hello,
I am working with the nRF9151 and would like to request the most complete available documentation describing all GPIO pins (P0.0, P0.1, ... - P0.31) and their functions...
I have installed ncs3.3.0 and want to keep ncs unaffected. According to the document docs.nordicsemi.com/.../sdk_setup.html , I should choose to import the edge impulse SDK...
Hello, we want to evaluate the BLE ISP2454-LX chip.
To do this we bought from RUTRONIK FRANCE an ISP2454-LX-EB evaluation board with the ISP2454-LX-TB test board.
SDK...
