Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I have a field application with a gateway (central) that connects to multiple peripherals for continuous data streaming, in this case 10 peripherals. I notice sometimes...
Has anyone successfully managed to control an led strip (WS2812) with nRF52840's I2S by any chance? I'm trying to use the led_ws2812 sample ( docs.nordicsemi.com/.../README...
Hi,
I'm working on a custom project and I was able to add and edit the overlay file according to my need till yesterday. Today when I tried to build the project I observed...
I am currently working on a Direction Finding project, but I am facing an issue in prj.conf .
I use an nRF52811 custom board for Direction Finding. In the board selection...
I am following the tutorial on Nordic Dev Academy I have a nrf7002dk board and I flashed the code present here . The problem is even if I configure only one channel and I...
Hi Nordic,
I am currently working with the nRF52833 development board and facing an issue related to the APPROTECT feature. Each time I connect the board, the access protection...
HI ALL,
v2.8.0, nrf54l15, using the "periphral_uart" demo without any modifications
I downloaded nrf52840 using v2.8.0 and it runs normally, but nrf54l15 has issues. ...
Hi there, I am trying to implement a UART handler on my nRF9151 that can Tx GNSS updates to my nRF52833. I am adapting this into the cellular/gnss sample, which is working...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hello, I am using the nRF52832DK with the peripheral_nfc_pairing example. With nRF Connect Mobile the NFC OOB pairing works fine, but when I try the same with my own Kotlin...
Hi
I've recently tried to move from SDK version 2.6.3 to 2.9.1. However i've run into issues with this transistion.
I made a new custom board, by following the guide...
Board: nRF5340-DK SDK: nrf ncs v3.0.2 Hi, On the project I am working on there is a tight timing constraint for DMA timeout (30-40us). Also there was a need for specific baudrate...
The current default and only recommended way to use MCUboot is to make the private key available as part of the build process.
There have been several questions about this...
Hi
we are using nrfx drivers for nRF5340 with gcc-arm-none-eabi and they work great. Now we are planning to move to another compiler and I have a couple of questions:
...
