GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi Nordic team,
I’m working on an nRF5340 project using MCUboot with the secondary slot placed on external flash.
I found a strange issue related to pm_static.yml . My...
Hello Team,
I am trying to test a PDM microphone (MP34DT01‑M MEMS) on the nRF9151 DK using nRF Connect SDK .
So far:
I have successfully tested I2C and I2S DAC audio...
The drag and drop programming was working fine on previous boards.
We just purchased 10 boards thinking that they were the same, but the don't seem to work.
PCA10040 3...
We are developing the nRF5340 for the Thingy91X based on Connectivity Bridge (NCS 3.2.4). I want to output logs from SWD and view them with RTT Viewer, but even when I call...
The spec. gives a 22V max for a limited amount of time. And max. 5.5V as recommended operating conditions.
But I wonder, what will be "inbetween", e.g. 7V for hours?
From...
Hi all,
I'm working on BLE time synchronization between nodes using hardware timestamps via GRTC + DPPI + PPIB cross-domain. CRCOK and PHYEND work perfectly, but adding...
Hi,
My main() program is
maiin()
{
int rc;
//rc = mcumgr_smp_client_erase(); //printk("mcumgr_smp_client_erase rc=%d\n", rc); //rc = mcumgr_smp_client_confirm_image...
The nPM1304 datasheet shows:
tshipToActive Duration SHPHLD pin must be held low to exit Ship or Hibernate mode: 96 (default)
May we know if debounce is applied to the...
Hi,
I recently started working with the nRF54L15DK and nRF Connect SDK 2.9.1. I'm trying to use I2C21 and SPI00, but I noticed that certain pins on the development kit always...
Hello.
I am experiencing an issue where Mesh communication fails after connecting to the SMP Service in the Bluetooth Mesh DFU Distributor sample.
Environment:
NCS...
Summary
On NCS v3.3.0 with CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y and a single Ethernet AIL interface (W5500), the Border Router never initialises:
ot br state → uninitialized...
Hello,
We are currently evaluating the nPM1300 as a key component on one of our new designs. This design must support both USB and solar charging using relatively low power...
I recently bought a NRF52840 DK board to teach myself embedded development. I am now following the nRF5 SDK tutorial here:
https://infocenter.nordicsemi.com/index.jsp?topic...
Good morning/afternoon all, I have been working on a BLE air quality monitor using the NRF52810. The first version functioned as expected with the exception of the external...
I am developing and testing in nrf5_sdk_17.1.0_ddde560examplesble_peripheralble_app_hrs_freertos. My project requires both BLE and a proprietary radio protocol, but BLE and...
