Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I've nrf52833dk board, I'm doing i2c exercise from Dev Academy's NRF connect sdk fundamental course. For some reason I used 'Quick Start' option in "nrf connect for Desktop...
Dear Nordic teams :
I would like to clarify the capacitor usage configuration:
1. If the firmware is configured to use the internal load capacitor and I also place external...
Hello,
I'm building a project on a Xiao nRF52840 Plus board. When I built and flashed the firmware, the Nordic LED Button Service does not appear in the nRFConnect app....
I have a custom board with bl54u and NPM1300 . Working fine.
But now replaced with a NPM1304 as it is pin compatible. Worked fine with fuel gauge NPM1300 on SDK 3.0.1. ...
We've derived a DTLS handshake test firmware from github.com/.../l5_e2_sol
Tests have been done using nRF9151 DK, SDK 3.1.0 and modem firmware 2.0.2.
First we verified...
I'm putting together a project that requires a "large" (1500mAh+) rechargable battery, both because of the desire for long times between charges and to enable powering a peripheral...
Hello Nordic Support Team,
I'm working with the Android-nRF-Wi-Fi-Provisioner library ( https://github.com/NordicSemiconductor/Android-nRF-Wi-Fi-Provisioner ) and would...
I'm using the Nordic nRF52840-DK. I'm having a hard time with logging using RTT. Sometimes it works, sometimes it does not. Usually I get a few runs where it works, then it...
I developed a custom application on the 52840DK and have now moved this over to a custom PCB of my own design. I can compile OK and can start a debug session from "main" but...
I am unable to download the nrfjprog command line tools from your website.
I am using SDKV1.8.0 and Toolchchain V2.0.0. in Visual Studio Code.
When I attempt to flash...
Hi,
I have low power environmental sensor. They raise an interrupt that something was sensed and require to read some registers on the sensor via I2C and run a state machine...
Currently, the nRF Connect extensions are available only on the Visual Studio Code Marketplace. We primarily use Cursor, which is a VS Code fork designed for enhanced AI-assisted...
Hello everyone,
I’m currently working on implementing the PK peripheral using Rust with the SVD files for the nRF54L15, but I’m running into a documentation issue.
In...
have a MONOGOTO SIM card that works successfully with TELIT and THALES modems. However, the same SIM card is not detected on the NRF9151-DK. When I send AT+CPIN? , I get:...
Hi I’m having trouble connecting to my nRF5340 dk using nRF Connect for Desktop (Programmer app). When I select the device, I get repeated errors like:
Details:
...
