I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I'm running s120 v1.2 & SDK 9
My application will connect to, up to 8, known peripherals. If the connection is dropped or not established, my central app will try to continue...
By trial and error, I notice that I can only write 20 bytes to a characteristic, no matter how big I make ble_gatts_attr_t.max_len. A little googling reveals that this is...
Hi,:
I run my application program by nRF51822, about S110 V6.0 and SDK 5.2.
When the program run servial cycle functioin , it is work normail.But sometime, nRF51822 sysytem...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hello Guys,
I'm about to start my first BLE iOS project and I was wondering if there are any compatibility issues or anything that I should be aware between nRF51822 and...
im running on mac with eclipse and tried to use debugger prints, but the don't show up in the console.
Same goes for printf and uart.
Is there a flag in the makefile preventing...
Hello,
I am checking to see if it is possible to use app_twi_perform() to transmit TWI transactions that have a High Write bit. I have changed the polarity of APP_TWI_WRITE_OP...
I'm developing an embedded application using the nRF52 device. I am using GCC to build the C software and a segger flash device to program the nRF52, all using linux. I wish...
I wrote this code found in an example and it works fine:
#include "nrf_drv_config.h"
#include "nrf_drv_timer.h"
//Before I activated TIMER0, TIMER1 and TIMER2 in nrf_drv_config...
Hi,
I am using eclipse IDE and gdb to debug and flash applications onto nrf52 dk. I wish to be able to print data and messages to the eclipse console. I work on mac OSX...
I'm trying to send data over UART... started off using the examples from the SDK.
When I run the code on the dev board, I can get it working. When I load the code onto...
I want to use ESB protocol, with app_timer module to generate timer interrupts. Is it possible?
If yes could you please send some example codes for it? thanks
Per the nRF51822 product specification the NVMC ERASEPAGE operation takes up to 22.3 ms, about 730 ticks of a 32 KiHz clock. This is 365x the maximum delay between the watchdog...