Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi all,
I am facing a weird issue trying to achieve DFU over the air with the dual-blank DFU.
I had integrated DFU with my application(Background story here .) The application...
Hi
I have problem enabling gzll on my nRF51. Error diagnoses shows NRF_GZLL_ERROR_CODE_INTERNAL_ASSERT_OCCURRED (#15), every time I try to call nrf_gzll_enable();
Here is...
I've looked at the reference manual and the several forum questions asking the same question and do not understand the answers as they all seem to point to the same docs/original...
HI All,
We are using NRF52, S132 Softdevice , SDK 11.0.0.
In SPI DMA transfer, when we try to increase size of the m_tx_data greater than 254 bytes, it failed. It is working...
HI All,
I did all the things as in this post
devzone.nordicsemi.com/.../
But Whitelist is not working for me. My requirement is this, I need to add the first connected...
Hi everyone,
I must to program my device from nRFgo Studio (rel. 1.21). So I do this procedure:
I program the Softdevice (in my application S110 rel. 7.0.0);
I program...
I am using nrf51822 and I am trying to reduce the transmit range to 30 cm or less.Is it possible to achieve this. The reason I am doing this is that I will be working with...
Hi,
I want to use both SPI master & slave altogether, but when I include nrf_drv_spis.h upon compilation the following error occurs :
C:\Keil_v5\ARM\PACK\NordicSemiconductor...
I am trying to find out the lowest range of nrf51822 but so far I coulden't find anything. Most of the time people are trying to increase the range.Thanks.
Hi Guys.
I have compiled and programmed ble_app_uart program in to a nrf51DK (pca10028-nrf51488).
I downloaded and installed nRF UART V2.0 to android 5.1.1 .But while scanning...
Hi,all.i use pwm with sdk8.1 sample (SDK8.1\example\peripheral\pwm),my question is how to stop pwm and set the pin to low level? is my code correct?
my pwm init code:
...
I've a board with the nRF51 inside and a LIS3DH as accelerometer.
I already reflashed and I want to read the accelerometer values from the LIS3DH but I don't know where...
Hi Guys,
I tried to integrate the spi master project to ble_app_uart. For that I added the missing headers from spi project to ble_app_uart. And also I added the .c files...
