Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
Hi, I want to run Bluetooth Mesh Light example on nrf54h20 chip.
At the beginning I prepared devboard with this tutorial: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hello,
I am trying to build a firmware for the nRF5340 on the Thingy91:x. The firmware should use the external flash for the secondary Image and is using the chained bootload...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
Hi,
I see that the nominal deafult rampup time is 140 us in NRF52.
However, I'm measuring it with logic (via GPIO+PPI) and I get 129.4 us.
Why there is such a difference...
Hi, I received an e-mail about the new nRF52840.
Nordic Semiconductor has today released the new nRF52840 multi-protocol SoC
with on-chip support for the upcoming Bluetooth...
Hello,
I tried the example code ble_app_proximty connect to android using nrf connect application, but why when i try to connect, nrf51822 can not connect, like example this...
Hi /.*/,
i just downloaded the newest version of the nrfjprog command line from the following site:
www.nordicsemi.com/.../58855
Unfortunately after i unpack the downloaded...
Gentle folks,
I'm sure I'm making some simple, primitive error. Please help me mend my ways :-)
Using gcc in the NetBeans IDE on MacOS for building and running the ble_app_hrs...
Hi all,
I have seen thread related to this question such as this and this and I am aware that spikes happen due the automatically controlled refreshing mode of the DCDC...
Hi,
I am working on ble_app_uart_c example provided in SDK12.3.0 with S130. I tried this example on PTR5518 ble chip but suddenly device goes resetted every time.I am printing...
I'm finding rather high power consumption developing freeRTOS on the nRF52. I have it found that it appears Task's are suspending properly on the main BLE thread (copied from...
Setup
I was just looking through the code in the HIDS module in more detail, now that I have built a few demo HIDS apps I want to make sure that I understand the HIDS module...
Hi,
Is there any other define to change than SERVER_COUNT in main.c of client's light control in order to run the example with only 1 client and 2 servers (instead of 3 servers...
I cannot get the output from the is the example the UART buffer gets filled but there is no output to the tty.
The interrupts seem to be set, but I don't see the interrupt...
Hi
I am using nrf52840 for indoor positioning application based on RSSI. I was wondering if somebody has a tip how to calibrate the nodes before doing the experiment.
Hi,
I'm using sdk12.3.0 ble_app_uart.
My problem is BLE connection.
Sometimes(almost 50%)I tried to connect BLE but fail and I have to connect again.
I don't know...
Hi, I'm contemplating ways to drive a small RGB LED matrix with the nrf52832 in a really space-tight project. Ideally without any external components. I'ts maybe around 40...
