Hi,
I am searching for the RED certification for the NRF54L15, but I can not find it anywhere.
Could someone please provide me with this documentation?
Hello,
I am using nrf52840 MCU.
I am developing a product which have 2 I2C and 2 SPI interfaces. All the interfaces are on different pins.
I developed this thing with...
Hello all,
I am using the nrf52840 MCU and NCS v2.6.2 for my application development. Here I am using SPIM3. I am using a peripheral which have an internal FIFO. From...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hi everyone,
I'm working on a project using the nRF54L05 (v2.9.0) and I'm currently facing an issue with BLE. I want to change the BLE transmit power , and so far I’ve only...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hello everyone,
i can able to set the static passkey but i would like to know the difference bewteen security key and passkey how can i set security key ? any suggestions...
Good day!
Faced with the problem that I didn't get to run N5 Starter Kit (nRF51422) on maximum speed in Advanced Burst Mode, using ANTware II with ANTUSB-m to read packets...
I read the multi-role project on Github. For time slot part, there's no explicit hfclk start/stop operation along with the radio events, is it possible that sd_radio_session_open...
In the nRF8001 Arduino SDK, there is a " ble_bandwidth_test " example.
It says,
"The bandwidth is measured (sic?) with the nRF UART App in the Apple iOS app store" ...
I am trying to communicate with a SPI peripheral, using the nRF52 as the master, and the peripheral as the slave. What happens is that it still faults out, and the presence...
We are currently developing an Android app (5.0) supporting the peripheral mode and communicating with the Master Control Panel (v3.7.1).
The connection to the Android...
Hi,all.i faced a problem:when i take my phone far away from my device,link lost service can work normal and my device can alarm.But if i turn off bluetooth switch on my phone...
Hello everyone,
i am trying to mix up both services proximity and RSSI but i am not able to merge the header files of these two services can anyone guide me? how to merge...
Hi,
I'm converting my project to OSX GNU from windows keil because of license problem.
There is some .o files made by keil-arm complier in my previous project.
and...
Hello,
Is that possible to force carrier frequency out of 2.4 GHz band (modify canals) for a special underwater application (2.4 GHz is not adapted so i whish to move on...
Hi,
I want to detect long and short press in same button.
Define "BUTTON_DETECTION_DELAY" can detect one delay.
Let me know to detect more than two delays.
Hi everyone,
I'd like to use the micro-esb radio interface to let to nRF's talk to each other. One of them will be generating 4 PWM outputs based on data received.
I have...
Hello Nordic,
I am trying debugging on following project [--ble_app_lbs_master--]. During debugging, I never reach at app_button_is_pushed function. I tried pressing the...
I have built a PCB that uses the nRF51822 . I am failing to load the binary onto the chip via the nRF51 DK. I can:
connect to the nRF51822 on my mac using the JLinkExe...
