Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi @ all,
We discovered a bug in the Nordic TLS API, which only appears once a secure TCP connection that makes use of certificates is to be established.
The provided...
Hello All,
I'm developing a BLE sensor based on the nRF52832 which needs to do the following:
Use an (i)Beacon for the user to find the sensor with an App on a mobile...
nRF52832 has errata about gpiote as below.
3.29 [97] GPIOTE: High current consumption in System ON Idle mode
So I want to use PORT event for gpio interrupt, but PORT...
Hi all,
I programed hex file (blinky example) to nRF51DK via nRFgo Studio, and the board could work fine (keep blinky).
However, the nRF51DK will work FAIL (LEDs are not...
Hi,
I need to monitor voltage very frequently, have access to the latest value and also to have interrupt on low limit.
But I do not want to have interrupt on EVT_DONE,...
Does anybody knows exact number of the "4 SIG fixed group addresses"?
Is it 0x00? or other?
In the SIG document, there is below chapter.
Group Addresses
A Group...
Hello Sir,
I have developed a product on nRF52832 DK kit and using S132 soft device. I want to flash this same hex file into SparkFun nRF52832 using nRF52832 DK. But i...
I'd like to use nrfjprog to read contents of QSPI external memory. (I'm using an nRF52840-QIAA on a custom PCB, based on the PDK.)
Using application firmware I am able...
Hello
i am using nrf52840 dk with sdk 13.0r3 software.
on first board, using example ble_app_hrs_rscs_relay example.
on second board, using example ble_app_hrs_peripheral...
Hi,
On my single I2C Bus, I have interfaced 4 I2C slave devices.. Now my voltage level of this bus behaves randomly. sometimes It shows 3.3V, but most of the times It stays...
Hi all,
We are currently under FCC certification testing for our custom BLE module based on nRF51822 but failed with the average power exceeding the limit. Nordic Semiconductor...
I'm following the tutorial Development with GCC and Eclipse, but have problem when use GCC to compile project that use PWM library.
I found that when compile the code with...
Hello,
I am getting data from UART and extract NRF BLE packet.
I check the CRC Flag and its OK. But sometimes the UART has some error and I have to check the 3 CRC bytes...
