after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi, I'm testing the light control example from Mesh SDK 0.10.1.
Although I have received an answer about the future plans of mobile Mesh SDK from developer Hung Bui that...
Hi,
I have some data which i want to send from nrf51-dk to ESP8266 . i have tried Ble UART central example to write data serially but doesn't achieve any result. I have also...
I have 2 Channels with SAADC taking samples. They are configured to respond to BLE characteristics that have read and notify properties, each channel has its own characteristic...
Hi,
As in the Product Specification of nRF52, pin number 9 and 10 are configured as NFC pins. However, this setup is conflicted with our pin mapping for other sensors in...
I am trying to store a small amount of data on the nRF52832 with the FDS module.
I followed the following code found in another question:
devzone.nordicsemi.com/.../...
Hi,
We are currently migrating our codebase from SDK 13 to SDK 14 for NRF52832 based board. One major difference we see is that SPI transfer completion callbacks are not...
Hi Dear Nordic!
We have prepared 200 pieces of PCB (used nRF52840) to pre-test our Product.
Now we are waiting for nRF52840 IC to solder.
Is it possible to buy ~...
Hello,
I've just found the Zephyr project which provides very interesting features and many questions are rising in my mind, but I don't know if this is the correct place...
I want use the NRF52832's NFC Tag in a bracelet. I need to know when the battery of the bracelect
is out, can the NRF52832's NFC Tag still be readable? Like the UID of the...
Hi
I add code in nrf5_SDK_for_Mesh_v0.10.0-Alpha_src, and when it run the follow code
and the ret_code is 4, I get information from the follow code
it is NRF_ERROR_NO_MEM...
Hi everyone !
I'm working with nRF 52840. I've downloaded softDevice s140 using Keil. Afterwards, I selected the target to nRF52840_xxaa and then build the project of Heart...
Not sure I understand the sentence. Do you guys mean "enabled"?
PSEL.SCK, PSEL.MOSI and PSEL.MISO must
only be configured when the SPI master
is disabled.
infocenter...
Lately I've been getting randomly occuring hardfault in my code during heavy BLE traffic and Sensor data collection times. From the hardfault_implementation.c loop I see the...
Hi,
Is there a size limit for the vendor specific service UUID? It looks like it should be 16 bits but I can't set more than 4 bits in my code.
I am using the uart central...
