after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
HI!
The use of simulation software I2C and the sensor module communication in my program, without the use of the protocol stack, the normal running of the program, but after...
Hello,
I am using sdk 12.2.2 and pca10040. I want to include the mac address in adv packet name. I am not aware of the api used to get mac address. I used sd_ble_gap_address_get...
HW: BMD-350
SDK: nRF5_SDK_12.0.0_12f24da
Sample Code: examples\dfu\bootloader_secure\pca10040_debug
I have my own firmware app.
Problem:
If I use Keil to flash...
Do I have to temperature dissipation? I attached temperature sensor on my board with nrf51822. I removed copper layer of around the temperature sensor. But it seems the temperature...
Hi,
I am using nrf51822(qfaa), sdk12.3, softdevice s130.
I am using the ble_app_uart (both central and peripheral) as reference for my development.
I have both central...
Hi,
I get following error when i try to compile nRF5_IoT_SDK_v0.9.x for target nrf52822
compiling x509_csr.c...
assembling arm_startup_nrf51.s...
(13): error: A1517E...
I'm working with LEDs in a ble example
I'm calling ble_notification_init() and activate the LED in the callback handler.
I get sd_nvic_ClearPendingIRQ, sd_nvic_SetPriority...
Is there a way to get the RSSI value of a message using the standard functions within the sdk for mesh. I am currently using a modified version of the simple_on_off client...
Hi all
I'm trying to send 180 bytes using sd_ble_gattc_write(). Writing 20 bytes at a time with the BLE_GATT_OP_WRITE_REQ write_op works. But now I'm trying to speed things...
When I tried S110 examples like BLE proximity, beacon and hrs on QFAC, it works without any problem. Unfortunatelly I can not see any activity on pin VDD_PA of CDAB. Is there...
Hello.
I used NRF51822 Dongle(Central) and Peripheral.
I want to change from Dongle(Central) to PC(Central).
PC version is window8.1.
but not operation bluetooth communication...
In the examples I see places where there is conditional code based on the #define HOST.
For example in function nrf_mesh_init() i see that the softdevice is only enabled...
Hello,
My team and I are experiencing a problem with our custom DFU Bootloader, which is based on the Experimental Bootloader Secure Serial example (SDK 13), running in...
Hello,
I'm reading on github.com/.../Android-DFU-Library that there is a support for higher MTU on DFU. Is there an example how i should test it?
I'm tring to increase...
