Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hello,
I am using sdk11 on NRF52382 custom Board.
I am trying to save around 1500 words in flash since the page can save approx 1000 words so I change the code to write...
Hi,
I am use nRF51422 and SDK 12.3 sd130.
I can use nRFTool App update FW to nRF51422.
but I dont know how to switch App to bootloader in BLE not button.
which function...
I have doubts about using the pstorage_init function in the example for SDK11 in this answer . Documentation says that this is module initialization routine but in the exemplary...
I combined ble_app_hrs of example with ble_app_hts of example .
I write command in client characteristic configuration,
there is a problem that ATT_ErrorRsp : status...
I have some problem with Interrupt vector,details as below.
I design a bootloader code,and in the bootloader,i use timer0 interrupt.Then in the app code,i use the timer0...
Hi all,
I was wondering if I can install Soft device for a BLE-module other than Nordic?
And if so, will it gonna work?
Thank for help in advance!
blueguy
Hello,
I would like to detect a change in a pin( GPIO_IN_NUMBER ) and depending on it I would like to trigger a SPI transaction, this should happen through PPI.
So far...
I'm trying to migrate my old app based on buttonless app sdk13 to buttonless app sdk14.
I solved issuie according to migrate guide remove chunk things and etc.
My app works...
I am creating an App for iOS using nrf beacon.
App is for garage door and i want to get notification when door closed or open, when beacon is in range or out from range but...
I am using nRF 52840 board. I used Keil 5 to load one of the examples in SDK successfully, but when I unplug the USB cable and used the battery. My program doesn't run properly...
We worked on the nrf52832 DK.
We will begin the prototyping phase. But the dev kit's antenna is too big. Can send me a reference and schematic of a ceramic antenna.
Other...
We have based our code off of ble_app_proximity. Upon first connecting to the advertising NRF51822AB device with softdevice 110 v8.0.0, we write to pstorage.
static void...
I USE IAR7.7 AND v11.0
THERE ARE ERRS.
FS_REGISTER_CFG(fs_config_t fs_config) =
{
.callback = fs_evt_handler, // Function for event callbacks.
.num_pages = NUM_PAGES...
SDK Version: 13 Alpha
I've been able to track down, through app_uart.h, where UART interrupt priorities are set using NVIC_SetPriority(). Now I'd like to know where interrupts...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
