Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
Hi,
Because of the compatibility issues I'm trying to use SDK10 for my nRF51422 device,
the problem is that I have flashed the S130 softdevice and the ble_app_uart, and...
I want to use FDS in my application. Lets assume I do not have a bootloader. This is part of my linker script describing memory regions.
MEMORY
{
FLASH (rx) : ORIGIN...
I am using proximity profile for my custom board as a tracker.I would like to make the services read/write operations accessable only to my andriod app.Others can connect...
Hello,
Recently I purchased a BLE Nano Kit with MK20/ DAP Link USB Board - Bluetooth 4.0 Low Energy Module Development Board from Fab2Lab and I was trying to use the nRF...
Hello,
We are new in Bluetooth development world. We want to use Laird's BL652 module. At beginning we want to use smartBasic and later Nordic SDK directly. Is it possible...
HI Nordic Team,
I had a production run of 5000 units. Used nrfjprog script to program the nrf51 .
Used the following commands:
nrfjprog -f NRF51 -e
nrfjprog -f NRF51...
Dear all,
I have a project with a nRF51822 based on S110 and SDK10.
Almost everything is running fine, but every time I scan for devices, either by calling BluetoothAdapter...
Hi,
I am writing an application for nRF52832 that uses both Flash Storage and Flash Data Storage in SDK12.2. I want to know how to get the start and the end addresses of...
hello,will you please tell me which code i have to use in the sdk 12.2.0 for rf communication with nrf51822 and nrf24l01 .and also tell me which settings i have to do for...
Hi
I'm working on detecting voltage change direction(up or down) by using LPCOMP or COMP.
LPCOMP initiates as following settings:
detection: NRF_LPCOMP_DETECT_UP.
reference...
Hi,
in want to extend the DFU library (Android and iOS) with a function similar to setBinOrHex(). But instead of a filename, i want to give a byte array with the init packet...
I think there is a bug in Nordic provided code in this thread about fetching the offending PC in a hardfault handler:
devzone.nordicsemi.com/.../
The provided code is...
I have found these 2 threads in this forum regarding this matter but I am a bit stuck.
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
I want to port the...
