I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
I added uart service ( here and here )
and I think in part of ble everything goes well. I have blinking led1 and can see all my services.
Then I tried add uart part.
After...
I have a custom board that has a nRF52832 device (receiver).
I am scanning for remote beacons (also custom boards with nRF82832).
The result is that I obtain the MAC of...
Hi I use 4 characteristics in peripheral and central. When I write to one of the characteristics in the peripheral, I read it using sd_ble_gattc_read in the central. But,...
Hi,
SDK14.0
nRF52832
I am using the dfu\bootloader_secure_ble example as my starting point. My goal is to create a very simple bootloader (with none of the dfu stuff...
Hi
We are trying to use the uECC library file (micro_ecc_lib_nrf52.lib) with our project that is built in Kiel. We have followed the instructions found here using the open...
Hello,
I'm using SDK 132 (v5), kiel 5, SDK 14 and the nrf52 dev board.
I'd like my application to have multiple Offical Services (Heart rate, Humain temperature,...
Hi,
For my new project, I copied the linker script and Makefile from examples/ble_peripheral/ble_app_uart/pca10040/s132/armgcc to a folder and changed the SDK dir and project...
Hi All,
I have developed a device using the nRF51822, and the connection interval is set to ~1000ms.
When reading a characteristic from a Raspberry Pi, we are timing...
Any updates on this from anyone? Please advise
Hi,
The i2S microphone that I am using requires a over sampling rate fixed at 64 therefore the WS signal (LRCLK on nrf52...
Hi community, I'm running a 51802 on my custom board with no other parts on it, except for some buttons and leds directly connected to GPIO, and a DC/DC converter which feed...
The term 'slot' is used in the context of the Eddystone beacon specification.
I cannot find a definition of that word.
For example, the sample app from Nordic says ...
I set up an account a few days ago on nordicsemi.com and today it's rejecting my login. I then requested a new password which was sent to my email but when I copy and paste...
I am studying how to update the firmware through BLE at the moment. I used the example project of "ble_app_buttonless_dfu", but I am having many questions that I don't understand...
Hello everyone,
My job is to migrate a functionnal code made with IAR to GCC Eclipse.
When I compile with IAR and flash the hex file (softdevice and application) using...
I'm using:
bootloader_secure example in SDK 12.3.0
SoftDevice S130 nrf51 2.0.1
Is a bootloader update 100% failsafe against power loss anytime during the process...
