Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
I want to add a timeout to the secure DFU bootloader if I enter it from the application. I found this post here devzone.nordicsemi.com/.../ but unfortuately I can't use the...
Hi I'm looking forward to hear if I could program an nRf51822 QFAA without using the development kit/board. The chip I have currently is a N51822- S4AT, from Wireless Tag...
we are facing problem with smt M905 module. is there any basic error with this module pad?
smt factory in china failed several times to solder this module.
Hi - In my app, I'm using Bluetooth, the ADC, the TWI, and the SPI. The general idea is to measure lots of things, store the data in SPI NOR FLASH, and occasionally flush...
I'm testing a custom application with the following configuration:
Custom app based on the ble_app_pwr_profiling SDK example.
Using SDK 13.1
S140 SoftDevice s140_nrf52840_5...
Considering that as soon as the connection is established (GAP Peripheral device receives CONNECT_REQ packet) and advertising is over.
Is it possible once the connection...
Can the smart phones or tablets be configured as a peripheral? If yes, why is this not common? Are there any limitations if a tablet/phone is configured as a peripheral device...
Hi!
I'm developing a project with nrf52832 and I'm getting some problems. The micro is only communicating with an accelerometer (MMA8453) and after some time the communication...
Hello,
I am implementing a custom service with several characteristics, one of which is the current temperature. A second characteristic notifies the user if the temperature...
Hello,
I'd like to upgrade nrf51822 QFAC custom board firmware via DFU and change SoftDevice from s110 to s130. Because of larger (than s110) size of s130 I haven't enough...
Hello,
i am using the Visualgdb with sdk v 13.01. i have Nrf52840
i was trying to read the DeviceID of ADXL345
i am using API from this thread
devzone.nordicsemi...
I have used pstorage before but when I add scheduler to my project I face an error in update function of pstorage that in debug I found error_code : NRF_ERROR_NO_MEM .
any...
In short:
Is it possible to connect a nRF51822 s110 peripheral from a central without the need for sending advertising packets (by peripheral)?
If (hopefully) yes...
Hello,
I am trying to create an application that sends a notification from the nrf52 to a smartphone when a sensor reading exceeds a certain value. Would the immediate...
Hi,
I have designed and made a PCB with the nRF51422 chip on it. I am programming the chip externally using the P20 header pins on the nRF51-DK. I am not sure whether the...
