Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
can somebody tell me where to find these error codes?
error = app_twi_perform(&m_app_twi, als31300_read_sensor_transfer, 2, NULL);
APP_ERROR_CHECK(error);
perform is returning...
Hello
I am trying to implement Device Information Service using the sample code "ble_app_bps_s110_pca10028" in nRF51SDK 7.2.0.
But I couldn't get any change when I edit...
Hello,
I'm using the openthread border router (wpantund) along with another end device running the simple_coap_server example that exposes a "light" resource.
I have connectivity...
The "Bluetooth Low Energy Characteristics" tutorial, a beginner's tutorial,
devzone.nordicsemi.com/.../ , uses a version 11 of SoftDevice. But I need a it in version 12...
Hello!
I use the NRF51228 board like this PICTURE
The ICs revision QFAAH0.
I use Keil-uVision 5.17 and ST-Link V2 from STM32F4 Discovery board to load firmware HEX as...
Hello,
I am just getting started with my nRF52832 and went through the first getting started tutorial . I use the SDK V11 with Keil and Termite as described and an iPad...
Hello,
I run ble_peripheral\ble_app_uart example from this link : devzone.nordicsemi.com/.../36
Used PCA10040, SDK 11, S132 2.0.0
I use Termite3.2 and IOS nRF toolbox...
Hello, I am toggling two separate pins at different rates but it looks like for whatever reason the when I go to clear one gpio register it clears everything. I understand...
Hello,
I would like to make use of white list advertisment for my heart rate application on my nrf52832 s132 pca10040, currently I am using SDK12.2, is there some example...
Hello,
I used translation software.
I'm looking into LDO mode and DC-DC mode.
However, I did not know what LDO mode and DC-DC mode are.
What are LDO mode and DC...
I'm working on a project that will utilize the nRF52832 as the Host and Controller and an STM32F3 as the application using serialization.
I've included the nRF5 SDK V14...
We just produced a PCB with a NRF51822-QFAB-R7, does Nordic provide a EMC test firmware that we can flash onto the chip? Basically need it be always transmitting....
Thanks...
I'm using the original BLE App UART from nRF5_SDK_14.0.0 on a PCA10056 Board.
The board is advertising, but if I want to open a BLE peer-to-peer connection, than the application...
