Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Android TV devices such as Nvidia Shield, Xiaomi MiBox and Nexus Player have support for voice input via their BLE remotes. I've researched it a bit to figure out how it works...
Hi,
I posted recently about having used the app_uart driver and having problems with an overflow breaking uart receive ( devzone.nordicsemi.com/.../)
I decided to try...
Hello, I have an error while building the project "ble_app_hrs_rscs_relay_pca10056_s140" with sdk14.0.0 on segger embedded studio 3.26 and gcc/clang.
When compiling nrf_atfifo...
I have newly purchased the nrf52 Development kit . Does it contains any pre-loaded firmware detectable on the ble scanner or nordic connect device, becasue I cant see any...
Hello,
I would like to use the button handler library (app_button) from the nRF SDK on my nRF52840 to detect pushes on pin P1.05. However, no events are detected when the...
HI experts
I have a nRF51-DK board. I have flashed it with S130 softdevice. I have also flashed it with BLE_APP_HIDS_KEYBOARD application example. I have made little change...
/DfuImpl: Setting object to Command (Op Code = 6, Type = 1)
Something like this printed in log cat and after this app is stuck ..rest of the process not execute..
If the nrf51822 device goes out of range then comes back in range, the application automatically reconnects with the device and tries to read a particular characteristic....
Hi,
We have a set of connected devices in a building of around 22 floors, may be around 6000 devices, can it connected using a nRF52840 Mesh network? Please let me know...
I used the 52810 board, with the SDK14. I modified the 52810 according to the official website related to the relevant definition. I can run the code but it does not print...
I've been searching and wanted to confirm that in SDK13, it's still on us to implement a timeout if a device is placed in DFU mode? As others have said, this just seems such...
Hi,
I am planning to enable autoconnect feature in our app, the same way it is done in nrf-connect app. Is there any way to get the code for nrf-connect app or any other...
Hi there, I was trying out the ADC example which is sampling 10 times the ADC and then generating the event NRF_DRV_ADC_EVT_DONE to process the data.
I extended the handler...
Hi, Im using Nrf51422 DK board.
When I try the ble_app_multilink_central example in the SDK12, it works on the DK board.
But it does not work in NRF51822. (NRF51822 QF AA...
Hello All
I planning make DFU over the air.before going to this experiment i want know some information
Any Soft device is fine or Required specific SD
...
