Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I use NRF52832 and sdk13.0.0 to develop my own application. I want to generate 1000 Hz Timer to trigger the ADC. I use the timer 1 to generate 1000 Hz. But when I use GPIOTE...
Hi,
In Nordic nRF51822, (please correct me if I am wrong), after I transmit 1 byte of data (since the transmit fifo is 1 byte long and receive fifo is 6 bytes long), I can...
Does the python driver support multiple dongles? I have a situation where I want to scan with one dongle and connect to devices with a second dongle. However, the collector...
Hello,
I want to use the PCA10040 to program a custom board running on 1.8V using the debug out port. Is this possible?
Also, is there a way to set up the PCA10040 so...
Device: nrf52, sd132 v3.0.0, SDK 12.1 (and also 12.3), freeRTOS, BLE peripheral, gcc-arm-none-eabi-5_4-2016q2
I am experiencing an issue which is causing our device to...
Hi everyone,
I am developing a remote control using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
Hi, now I'm using NRF52832 's UART with SD12 and it required to receive 40 bytes per 10ms.
In fact, it does not take 10ms to complete the reception.So my idea is to create...
Hello,
I'm working on a type of activity tracker using the NRF52, and I'm a bit stuck with time aspects.
The device stores two versions of activity data; daily totals...
Hi
First I wrote a post because the initialization was crashing, but now I found out it was because the RX line was low.
How to initialize the uart if the RX line is low...
hi i have a problem with ble app uart.i used nRF5_SDK_12.3.0_d7731ad and Eclipse Mars 2.
I had build main.c in hex ble_app_uart\pca10040\s132 . And after that a maked mergehex...
Hello,
I am trying to update our application with DFU support but it will not work for me. One of 2 things happens:
Programming the bootloader and softdevice by programming...
Hello,
We have the following setup:
SDK Version: nRF51_SDK_8.1.0
bootloader Version: dfu_dual_bank_ble_s110_pca10028.hex
soft Device: s110_nrf51_8.0.0_softdevice...
Hello,
I'm working on a concurrent role device (advertiser+scanner+peripheral+central) and devices are configured to connect each other in a mesh-like way (Note: I'm not...
Hi,
i am using ble_app_hrs_c_pca10056_s140 and when connected to one particular device i need to access it's GATT profile services and characteristics.In example ble_app_hrs_c_pca10056_s140...
