Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Okay so the issue is a little more complicated than this.
Phones used for testing were htc m8 (android 6.0) and lg g5 (android 7.0).
Ble chip running on a linux OS using...
Hello, I'm using this code(observer):
github.com/.../nRF51-multi-role-conn-observer-advertiser
SDK9.0.0
I try to add DFU function, now can enter dfu mode and iPhone6...
Hi Nordic Team,
Can you please share any information regarding Indoor Location Tracking feature/application that nRF52840 can support? does this have AoA/AoD? and can this...
I want to establish BLE connection and have a central device receive data from a peripheral device. I am using the Heart Rate Collector as an example and notice the main file...
Dear All :
Is it possible to creat a pwm with 1sec period?
Since the lowest frequency of the base clock is 125kHz，the top count of the pwm with 1sec period will be 125000...
Hi.
I havent found answer for - in my opinion - common question - how to temporarily change name of ble device on button press. As long as button isnt pressed - advertise...
Hi, I'd like to know if there is a way to subtract two different square waves that are coming from two different input pins and then measure the pulse width (or the frequency...
I have been using Power Profiler Kit nRF6707 for awhile without problem. If I made a mistake by downloading firmware when the PPK is attached to nRF52 DK, the software on...
I followed this tutorial in Infocenter and installed everything infocenter.nordicsemi.com/index.jsp , but I have a problem with Thread examples, programming output looks normally...
Hello,
I am working on nrf52840 EVB , i programmed the board BLE_APP_UART but this profile is not working , still the board functioning previously programmed blinky example...
I'm not sure exactly how to word that,
I am about to try and get the adafruit feather to consume less power in standby and I've been told the arduino library isn't well...
Hello,
I am using pca10028 and sdk 12. I want to use 2 uart for my application but as per datasheet nrf51 has only one hardware uart. Can I implement soft uart on pca10028...
Hi, I would like to measure the electricity consumed at my home(220-240V) with the nrf 51822 and send it over bluetooth. No problem on the bluetooth side, but how can I measure...
I have a buttonless device using a DFU bootloader and ble_dfu buttonless DFU service with SDK v13.0.0. I'd like to make the ble_dfu service available for 5 minutes on power...
Hi Sir,
I am using nordic nRF51822 IC for Tracking Application for that Which antenna is best ?
I have seen two type of antenna .
zig zag pcb antenna
straight...
