Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
I have a Redbear BLENDv2 and want to program it with Keil. I am new to both Nordik SDK and Keil. Any help how to get to the example or open the example projects
Hello,
My question is about the case when initiator device attempting to restart encryprion with previously bonded responding device that lost the bond context.
As usual...
Hello,
I am trying to interface bme 280 with nrf52. I am using sdk12.2.2 and referring code twi_sensor.
I am able to initialize the I2C drivers and I can read the chip...
Hi,
My name is Bruno, and I am working with a Bluetooth module from u-blox(NINA B112-00B) which contains a nordicSemi board nRF52832 with a Cortex M4 processor. I'm getting...
Hello,
I am trying to combine Softdevice, bootloader, and Application hex files in single hex file.
Currently using s130, SDK11, nrf51822.
I combined files using this...
1, run NRF52832\nRF5_SDK_13.0.0_04a0bfd\examples\peripheral\uart, uarte_irq_handler can get irq when receive a byte.
2, run NRF52832\nRF5_SDK_13.0.0_04a0bfd\examples\proprietary_rf...
Hi,
I made an experiment and the result doesn't correspond with my view on how the BLE communication "connection" mechanism works.
I have an app running on the nRF52832...
Hello All
I am using following SDK version 12.2.0.i am facing some problem in some example project
could you please help me
If i flash the pre compiled hex file...
I held the boot button to enter bootloader mode, and accidentally dropped a hex file into the drive that popped up. Now I can no longer get a comm port to show up on the PC...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
(nRF51822, but also concerned with nRF52832, SD130, SDK 12.1)
I'm trying to write/erase flash from a bluetooth event handler. As it's been outlined in other questions,...
Hi,
I am just updating my application from SDK13.0.0 to SDK14.0.0.
2 Services are in use: DIS and NUS. To advertise that, I made use of the scan response functionality...
Hi,
I have the D52QD2M4IA-A chip (from dynastream) that has inside nrf52832 chip. It has also builtin an onboard LIS2DH accelerometer. However when I am trying to connect...
Hi,
I am working on nrf52832. I am preparing application where I need to handle central connection with two peripherals and keep tracking time. I know that softdevice has...
The data sheet recommends that both the TWI clock and data lines use pull ups and the GPIOs should be set to S0D1, essentially open collector drive. I can see the need for...
