When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hello everybody!
I have one nrf52840 DK and nrf528323 DK. I was flashed and test throughput example. I reach 450kbps. ( transfer 1Mbyte in 18s). Can I enhance this speed...
Hi,
We are interested in nRF52840 and we know that nRF52840 supports both on IEEE 802.15.4(Thread, ZigBee) and IEEE 802.15.1(BLE).
However, does nRF52840 can run BLE...
HI
I'm studying how to control mouse and keyboard via HID with nRF24LU1+ module referring to firmware of nAN-22.
Even though I set Descriptor as appropriate for mouse...
I'm using FDS and define record_chunk.length_words 173.
system waits for fds operation is finished and in the meanwhile, system sleeps using sd_app_wait().
Then, sd_app_evt_wait...
Hello
i am using BLE Relay example with softdevices 132 and sdk version 13.
i make this example simple, no more connection.
just adverting and scanning continuously. here...
Hi all,
I'm using nRF52840 and S140 based on the ble_app_uart example. I get a error code 4 when use sd_ble_gatts_characteristic_add to add a characteristic for another...
Hello,
Help me, please.
I am testing ble_app_uart. Softdevice is S130 and SDK is nRF5_SDK_12.2.0_f012efa.
My development board is Waveshare's NRF51822 Eval Kit.
...
Hello,
I'm writing an application that uses the SAADC and would like to set up a high limit to trigger on.
If I use the following code, I'm able to trigger 1 ADC sample...
Hi,
I plan to design a system of 51822 that includes 1 center and 2 devices. And 8K Bytes data should be transmited from each device to the center per second simultaneously...
Hi, I am using a two nRF24L0+'s.
One for TX and one for RX. Transmitting in one direction only. There is sometimes a packet arriving out of order. Every minute or two....
I use ESB sample code ,change to do 8k sample rate ADC(10bit) and transport by ESB ,but overflow when output receive data to PC use uart at UARTE_BAUDRATE_BAUDRATE_Baud1M...
Hi all,
I was trying to test the SDK13 ble_connectivity example being able to compile it when the NRF_SD_BLE_API_VERSION == 4 , but it seems like there are not pc-ble-driver...
