Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
FDS uses softdevice API. SDK 14.0.0
FDS writes are all successful for the same file id and different record keys until the flash is full
fds_delete_record() is called...
Hi,
I'm developing software for the nrf52832. However, I can't use the SDK of Nordic for several reasons.
In the code, I would like to save a small amount of data...
I tried to assigned each device to different group(subscriptions) by the following code segment.
for (uint16_t i=0; i < devCnt; i++) {
......
ERROR_CHECK(config_client_server_set...
Hello Everyone,
I am trying to incorporate NFC-BLE pairing feature in my ble_app_uart example. I have imported all the necessary files to the project and have installed...
Hi,
I am working on the project as a MultiLink example. My environment is using nRF52840DK & Softdevice 6 & SDK15.
I am trying to make multiple connections and communicate...
Trying to understand how the Device UUID is derived.
in iOS, Device UUID: FC7C7422-2BCF-894B-E848-855791DD3DD9
in RTT:
DEVICEID0: 0E064007 DEVICEID1: 14669F75 DEVICEADDR0...
Hello.
Hello.
I am trying to install pc-ble-driver-js on my computer but it fails to install. If anyone could guide me how to install it, that will be appreciated...
I'm having a strange problem where the Supervision timeout does not seem to work right at the point the connection is initiated (sd_ble_gap_connect() was called but BLE_GAP_EVT_CONNECTED...
I'm using the SPI in slave mode and have a very high power draw: > 2 mA. The issue happens both in my application + custom board as well as with the dev-kit + SPIS example...
Hello
I just have some small queries.
Let's say that I am scanning continuously for advertisement packets. I think the MAC address of the devices sending these packets...
Hello
We have two boards PCA10040, client and peripheral. Blinky exemple.
The project is with two buttons on peripheral side and 2 leds on the client side.
If we hold...
i haven't seen any code posted for the HC-SR04 ultrasonic distance sensor connected to the nRF24LE1, so i rolled my own, see below. it works well enough. the sensor runs on...
Hi all!
I've been working on a firmware to timestamp GPIO events using PPI in nRF52, and it works:
github.com/HiveTracker/firmware (more context: hivetracker.github.io...
Hello,
We're preparing to build a new application based on the examples available in the Mesh sdk and wondering if you have any tips on how to extract only the files needed...
I run a basic code on nRF52832 and measure the power consumption of the chip (using DVM). The current consumption is 400 uA which is a lot just for a single timer in my application...