Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi all ,
i'm using nRF51 DK ,im getting issue while program downloading on flash .Program compiled correctly(no any error) even it show flash downloaded but the application...
Hi There,
I have been looking into how to connec my QSPI NOR Flash to the NRF52840.
I have notivced a discrepancy between the comment in the Table 3. of the OPS and the...
Hi,
I have a peripheral which sends data to the central and from central i n eed data to be send to Mobile App
is it possibe to do and how???
or any other ideas you...
I am using Keil 5.24.2
I already downloaded and compiled with build_all the micro_ecc. Having no issues here.
According to the error, and what I read in another thread...
I have been investigating the possibility of using the QSPI external flash peripheral on our NRF chip. After doing a typical qspi read command, the external flash chip would...
Hi,
when i make a connection to my device i get 4 `BLE_GAP_EVT_CONN_PARAM_UPDATE`.
If i make an action of read or write when update event occures i get a duplicated read...
Greetings,
Here's an implementation of controlling the color of a RGB LED with a TIMER of nRF51. It works well most of the time, although it inverts polarity kind of randomly...
Hello,
I am using a Nrf52382 custom board and want to know the Vbattery so I used below code
#define MIN_BATTERY_ADC_VALUE (int16_t)11295 //(min_voltage_on_analog_pin...
Hi,
We have developing ble mesh network using nRF52 mesh sdk is 1.0.1. We have large amount of sensor data it near about 24-25 kb and want to send this data to other node...
I have an application that has been built using Arduino boards and shields for prototyping, and software developed using their IDE...all works fine.
The device comprises...
Hi all,
I am trying to use the SAADC to measure battery level. I have a rechargable lithium battery connected to my customed PCB with a NRF52832. The rechargable battery...
Hello. I have as question about the sd_ble_gatts_hvx. According to the API documents, the call to sd_ble_gatts_hvx will return NRF_ERROR_FORBIDDEN in the following situation...
Utilizing two nrf52832 dev kits, both flashed with v6 of the SD and using V15 of the sdk.
Using two examples from the SDK, the ble_peripheral/ble_app_rscs and a slightly...
hi. all. i have a problem:
1 . i use nrf51822 aa download nrfready_desktop_2_v3.0.0, sd+boot+desktop_keyboard, bud when i press p014 pair key, phone can not find device...
