Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hello, I want to create a simple example code with the leds ws2812b from neopixel from github.com/.../nrf51-neopixel. I need help to build the code.
Regards.
I'm converting an SDK 14.2.0 project to SDK 15.0.0 using the legacy functions and ARM GCC. It compiles OK but linking is failing.
The verbose output appears to be the Make...
hi i am trying to communicate with two devices throught UART , in nrf51 device uart i get a voltage of 2.83 v with .0238 milli ampere while in gsm module uart pin i have 4...
Hi Sir,
As reference RF5x support within the Zephyr Project RTOS , we can run Bluez in Linux environment.
But do we have the bluetooth stack in windows that we can work...
Hi all,
BLE newbie here.
I have a peripheral device (iBKS105 beacon) configured with Eddystone and iBeacon protocols, emitting on channels 37, 38 and 39. I set the advertising...
Hi, I recently started to work with the nRF52 DK (PCA10040).
I'm trying to do some experiments with PWM, so I toke the pwn library as a base and tried to add the button...
Hi I am trying to perform BLE compliance test on a nRF51822 based DUT. I want to connect the DUT to the tester using nRF51 DK. The nRF51 DK will be connected to the tester...
Hi,All,
I am using nrf52832 as a slave, the SDK version is 12.3. I set the connection timeout to 10s as follows
#define CONN_SUP_TIMEOUT MSEC_TO_UNITS(1000, UNIT_10_MS...
Hi,
I'm having an issue to connect a Galaxy samsung Tab A to my ble device.
Each time i ask for a connection i get the same error.
I already succeed with others phone...
Hi,
I'm trying to obtain as much information as possible about my usb connection with Nordic chip. I'm working on DK board with nRF840, sdk14 and usbd_msc example. My problem...
Hi,
I am using a chip labeled with "N52832 QF ABB0 1717AQ".
According to its specification, this chip should have 256kB flash. However, nRFgo Studio shows that its size...
I'm currently using matlab to perform a non-linear least squares regression to fit a line to an array of samples polled from the ADC with roughly 100 data points. Is something...
Hello,
Did anyone succesfully used meshctl from Bluez with Mesh serial example? Looking at both it seems that it should be doable but the tricky part is figuring out the...
i use ble_app_uart to send data to centrol, and i don't need the UART peripheral, so diabled uart with it: NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled;
but the problem...