Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi,
I'm expecting using a custom board with nrf52832 running connectivity program as a host to connect to the perpheral, and the hrc v5 example of pc-ble-driver is used...
hello support team
I am trying SDK Proximity coexistence example
I am using Mesh SDK 2.2
and nRF5_SDK_15.0.0_a53641a
I followed the steps given in link
I am getting...
Hi All,
i am working on SDK-14.2, i am facing issue with ble disconnection in dfu mode.
by using nrf-Connect in mobile i am upgrading the firmware, but it lost connection...
Details:
nRF52832
SDK 14.1 with matching SD
Compiling with GCC
I am trying to solve the following problem:
My device is powered by a coin cell (Manganese dioxide...
Hi, when my program calls sleep_mode_enter(), it enters system off (deep sleep) as expected. However, when I press the button on the Thingy52 to wake up, the bootloader starts...
I have problems connecting to a NRF51802 via stlinkv2 and openocd. I also tried a black magic probe flashed onto the blue pill board. Both did not work. I have ordered a NRF51822...
SDK 15.2
The nrfx_uarte_event_t callback contains a nrfx_uarte_xfer_evt_t; structure,
this structure has the bytes field as a uint8_t this should be a uint16_t to support...
Hi,
I'm using nrf52dk and SDK v15.
In my application, I have 2 input pin and I want to disable one of them when in one of the 2 pins occurs the event low to high, is it...
Hi All,
I have an issue with bootloader, in this i am successfully transferred application but after that my application not started.
i am just upgrading the sdk from...
Greetings,
I'm having the same weird issue as this question, though I don't understand the answer to it https://devzone.nordicsemi.com/f/nordic-q-a/34447/app-gets-stuck...
Hi everyone,
I've a nRF52810 based device that I am working with the Android based nRF Connect app on a Poco F1 (Oreo 8.1.0). The app scans the device properly but connection...
I just got my new nRF52840 dongle and went through the procedures stated. But I tried programming the nrf blinky firmware and after that I'm not able to connect the dongle...
Hi,
I am relatively new to the Nordic family of chips and I am very impressed with the level of documentation and support available, so many thanks for that.
I am working...
