I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Please tell me how to change the communication data length of BLE communication to 244 bytes and shorten communication cycle. Thank you.
I am using the version of [nRF5_SDK_15...
I know that there is a similar question here but the problem that the question is pointing on is not solved. Even in one of the answers is mentioned:
Now I found that...
When I run the example "ble_app_hrs_rscs_relay_pca10056_s140" on the development kit while debugging, then the SVC call for enabling the softdevice will stop at Address x8C4...
Hi! I want to implement at BLE switch(PTM215B) to a nRF52 DK, The switch sends advertise messages with switch status data. So i want to create a simple central that scans...
nrf52832 code always block at nrf_spi_event_check, my application include a app timer 200s period, after timeout, drive spi to get a RF sensor for sending some data, and also...
I am working with the nRF52832, SDK14.0.0. I want to perform a flash write on a watchdog reset to save the current state. However, the watchdog resets after two cycles of...
I've used the 'secure_bootloader' project, updated with the public key, to flash on the DK. The project 'ble_app_buttonless_dfu' built and packaged as zip can be DFU'd with...
Is it possible to _send_ multiple packets per connection interval, using the pc_ble_driver (and a nRF52 or nRF51 DK) in BLE CENTRAL role?
I found some answers on the devzone...
Hi, I developed a static library including drivers for spi, twi, gpio, adc and few others. Now when I create application and link my library it works ok as long as I am using...
Hoping to get some help. Using swift3 and xcode 9.3.
I can write data from iPhone back to nrf52 peripheral fine if it is a Dbl.
When I try to write a UInt16, it crashes...
I plan on using the nRF51 Dongle meandered antenna for a design involving the nRF52810. Since the nRF52810 has an internal balun, does that mean that L1, L2, C5, C4, L3 and...
hi,
i have a custom board with nrf52832 as it's core. i want to program with st-link v2 programmer.
i am using sdk 14.2 and soft device s132 v5.0. on target location we...
Hi guys,
We have tested the mesh range in the nRF52840 chip (max tx power) in LOS and we got more than 200m.
W're planning to use the mesh network inside hangar with a...
