Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
51822 problem: the device unexpectedly restarted, the current of the device becomes more than 800 ua, and the same as the jlink download current; the software reset current...
Hi
I have been trying the various examples from the SDK with Keil V5.23. Some work, some require changes to IROM1 and IRAM1 before they will run Initially giving an error...
I am trying to change the mac address of my device every time I advertise a packet. I have a callback on_ble_radio_active_evt where I update the address like this:
...
(I'm developing a firmware on nRF52832, but had actually stareted on nRF51822 and observed the same issue, SDK 12, pending migration to SDK 15)
When my app starts, I output...
Hi all,
I am investigating different protocols to support a network of very low-power Devices and Hosts. The Devices are mostly static (i.e. they don't move around very...
Dear developers,
I am developing a scheme where the nRF51 (central role) connects to iOS device (peripheral roles). The nRF51 connects, performs the discovery procedure and...
Hi,
I developed an application on the nRF51 Dongle (PCA10031) and am now trying to port it to this module. It is a nRF51822 AA device (256K Flash, 16K RAM), and it is Rev...
Hello everyone, I'm currently working on a project and I'm encountering issues.
The project involves with a BLE and a smartphone. The goal is to send Data from an application...
Hi
I have successfully(?) altered my application from using BLE_GAP_PHY_1MBPS to BLE_GAP_PHY_CODED. But how can I test it?
Prior to the modifications I tested the application...
Hello.
I'm trying to add encryption to the secure DFU bootloader. I'm using SDK v15. I know this topic has been discussed on this forum before. In particular I have found...
On NRF52840 DK, I don't have a softdevice installed. I want to do DFU with s140 softdevice only update. But it gives the following error:
raise NordicSemiException('Extended...
Hi,
I got a problem that doing the DFU through buttonless example, but successfully upgrade only in bootloader.
I used OPPO R9s (Android 6) with my personal cell phone...
which pin to use for TWI method communication, in board type 10040 nfr52832 model Taiyo Yuden EKSHJN
in file 10040 I have this definition of pins: what should i change...
Hello:
I have been at this problem for days now and not getting anywhere to a solution. My app is using a static passkey for encryption and does timeout after 30 seconds...
Hi,
I'm experimenting with incorporating " ATT_MTU Throughput" Example into our project.
I'm using nRF52832 as the peripheral and a SDK52 as the central.
The central...
