Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
in my tutorial I need to implement an I2C or TWI sensor on a peripheral BLE. In SoftDevice Software in Example-> Peripheral there are 2 methods 1) twi_sensor or 2) twi_master_with_twis_slave...
I used nRF Mesh app both iOS and Android versions to communicate with
nrf5_SDK_for_Mesh_v2.0.1_src\examples\light_switch\client
and
nrf5_SDK_for_Mesh_v2.0.1_src\examples...
The system consist of two nRF52832, one acting as SPIM and the other one as SPIS. I hace created a while loop always asking for certain amount of bytes but the MISO line on...
Hello, I am new to nRF micro-controllers and using Netbeans. I have cloned the repo of a project I would like to run, which builds successfully, and am getting the following...
Two questions. 1) What is the point of the watchdog ISR? In the Ambiq Apollo 2 microcontroller, the watchdog ISR fires and if the CPU doesn't pet the watchdog slightly after...
Hello I have problem with Mesh Serial Example and Interactive_pyaci, it works just in Debug-Mode. I use nRF52840, nRF5_SDK_15.0.0_a53641a, nrf5_SDK_for_Mesh_v2.0.1, Python3...
Hi I am trying to optimize my nrf51 app for low power. However I can just reach 0,500mA when just advertising (advertisement only is ok for me). Do you know or do you have...
I am trying to integrate the NFC read/write functions in my BLE application. I have used the writable_ndef_msg project functions to start with. The project on its own works...
Hello
For my final year project at Varsity I am creating my own smartwatch + edge computing IoT system. The watch and infrastructure needs to be as low-cost as possible...
Hi,
I am using a nRF52 DK board and programming in python.
After performing a successful DFU over BLE i want my Target device to be disconnected from the nRF board so...
thanks for the answer on the previous post.
What I came to know from our firmware engineer was that your initial version of the Android app could not support
1. multiple...
I want to know 2 things about the nRF Mesh app:
1) Is it possible for the Mesh app to provision non-proxy nodes via the proxy nodes?
2) I think it's possible to subscribe...
I have a project using FreeRTOS with Tickless idle enabled, SDK 11.0.0 alpha and the S132 soft device. Currently the project is consuming ~6.5mA average, ~5.2mA if advertising...
Hi There,
I very new to Nordic BLE application and was looking for method to combine ble_app_beacon and ble_app_blinky togather and having both switching and running at...