Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello,
This is a show stopper! I cannot get any Logging to neither the Segger Debug Terminal nor the JLINK RTT Viewer installed by nRF5x-Command-Line-Tools_9_7_3_Installer...
Hi, Just to say that the nordic devzone website does not work with Vivaldi navigator For example, this link below opens correctly with my opera navigator, while it fails with...
Hello, we are trying to implement PWM function with an incrementing/ decrementing duty cycle using a logarithmic function rather than linear function. Is there any predefined...
Dear Sir,
I wanted to connect the peripheral device to a phone which has highest rssi value(where multiple phones will be sending requests).
For that I have enabled...
in Mesh SDK v2, simple on/off model example, client node doesn't act as a provisioner.
But I still want to combine provision & client in the same device.
Is that just...
Hi all,
I'm reading the ble_peripheral samples of the SDK. I know start a advertising with the function ble_advertising_start();
Now, i know a central address, then i want...
I'm using the PPI to generate a PWM signal on my nRF51822, and I've noticed that TIMER_SHORTS is never triggered unless the timer interrupt is also active. I had originally...
Greetings,
I believe I'm seeing the same issue as this DevZone ticket: https://devzone.nordicsemi.com/f/nordic-q-a/23903/gpio-behaviour-during-power-down-nrf52832/94059#94059...
Hi dear all !
the Question is very simply,
1. What the real RESET VECTOR (isr table) , ROM address for nRF52840 MCU ? I mean what happened each time after MCU CORE reset...
Using a nRF52832-DK and nrfconnect-2.0 on Win 10 everything works well.
But using that with Ubuntu 18.04 requires more installation documentation!
1. it seems, that the...
How many GPIOTE Tasks can I use at the same time. I want to drive six different pins with six different tasks which are connected to three events. Each event generates two...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I have a peripheral (nrf52832) which is using a higher MTU (140 bytes). When I connect to it using the nRF Connect Android app, everything works. I can see the BLE_GAP_EVT_PHY_UPDATE_REQUEST...
Hi all,
I'm working with Nordic Thingy:52 (nRF6936 with nRF52832 inside).
Currently I'm working with original firmware (I mean, not modified firmware) version 2.1.0. But...
Hi,
I am debugging an SSD1306 OLED library, and in the datasheet, it does not explicitly mention support for repeated start bits. But using the nrf_drv_ API's with NRF_DRV_TWI_FLAG_TX_NO_STOP...
