Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi, I would like to create a new target,but nRF52810 only can be compiled with makefile and I don't know makefile too much.
I try to edit the makefile with my own target...
Hi guys,
I'm using following setup NRF51822, SD130, SDK 12.3.0. I control one transistor with PWM output via timer 1. Before enabling PWM I start 8bit ADC task to measure...
Does the Nordic UART Service (NUS) have a facility to confirm when a sent message has been received by the peer?
In particular, to confirm when an NUS message sent by a...
Good afternoon,
We are using NFC on nRF52840 (Type 4 Tag, SDK15.0.0, Softdevice6.0.0) to exchange some data and we would need to be able to do the following, please let...
Hello everyone. I am using micropython to program on nrf52840 DK.
This is tutorial which i read https://circuitpython.readthedocs.io/en/latest/ports/nrf/README.html .
...
Segger provides great information for the use of the JTrace for tracing and profiling with the NRF52 development kit here.
https://wiki.segger.com/Tracing_on_Nordic_Semiconductor_nRF52832...
Hi,
I'm expecting using a custom board with nrf52832 running connectivity program as a host to connect to the perpheral, and the hrc v5 example of pc-ble-driver is used...
hello support team
I am trying SDK Proximity coexistence example
I am using Mesh SDK 2.2
and nRF5_SDK_15.0.0_a53641a
I followed the steps given in link
I am getting...
Hi All,
i am working on SDK-14.2, i am facing issue with ble disconnection in dfu mode.
by using nrf-Connect in mobile i am upgrading the firmware, but it lost connection...
Details:
nRF52832
SDK 14.1 with matching SD
Compiling with GCC
I am trying to solve the following problem:
My device is powered by a coin cell (Manganese dioxide...
Hi, when my program calls sleep_mode_enter(), it enters system off (deep sleep) as expected. However, when I press the button on the Thingy52 to wake up, the bootloader starts...
I have problems connecting to a NRF51802 via stlinkv2 and openocd. I also tried a black magic probe flashed onto the blue pill board. Both did not work. I have ordered a NRF51822...
SDK 15.2
The nrfx_uarte_event_t callback contains a nrfx_uarte_xfer_evt_t; structure,
this structure has the bytes field as a uint8_t this should be a uint16_t to support...
Hi,
I'm using nrf52dk and SDK v15.
In my application, I have 2 input pin and I want to disable one of them when in one of the 2 pins occurs the event low to high, is it...
