Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello im trying to send data to mobile application, im using the example on ble_peripheral/ble_app_uart but when i compile the folowing error apears.
inking target: _build...
While writing our nRF5 based application, we have used an app_config.h in our project. This is advised as one of the solutions for updating the configuration of the SDK in...
I am a college engineering student. I currently have the NRF51 Bluetooth beacon along with the dongle I am in need of help uploading my code to the beacon via the dongle....
I have just bought an nRF51 Dongle and want to use it like a normal USB Bluetooth Adapter for my Windows 8.1. I have read the Getting Started Documentation, but there are...
I am struggling measuring time between two events. I thought to use the timer driver and the nrf_drv_timer_capture_get function and start/stop the timer with nrf_drv_timer_enable...
Dear Nordic,
I am try to implement RTC(nrf calendar implementation) in BLE example(SDK 13.0). both are working independently fine but combination of works fails RTC when...
My nrf51 SDK version is like this, nrf51 9.0 softdevice 130 chip:nrf51822_xxAArun ble_central_and_peripheral connectivity example, The nrf51 board is controlled by host MCU...
Hi All, the I/O mapping is correct as per the Ref Eval schematics. We are using a J-Link programmer to program it. The IC is not being detected in NRFgo studio. Can anybody...
Hi,
I was wondering if there is some documentation relating to pairing and bonding.
What BLE events (BLE_GAP_EVT, ???) are to be expected?
What do we need to observe...
I use ble_app_uart（sdk 14.2） + light_switch（mesh1.0.1）
Questions are as follows:
1client + 1server is ok, but in the second server there will be network failure!
log...
Hi,
I'm trying to get the tftp example working from the sdk iot examples. When I try it out following these instructions ( http://infocenter.nordicsemi.com/topic/com.nordic...
Hello,
i'm using the BLE Nano v2 with the nrf52832 on it and a DAPLink USB-Dongle. IDE is Eclipse with gcc and SDK v14.2. My current aim is to do an OTA DFU so I tried the...
I have a custom board, that basically consists of a nrf52832 module (ebyte), a button and a LED. The LED is connected as in pca10040: VDD->220R->LED-> ground to p17.
I assume...
Hi, I'm attempting to run the Proximity example ("ble_app_proximity_pca10028_s130") on my nRF51822 dev kit using the S130 SoftDevice. I am able to connect to the dev kit ...
