Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi i get this error when compiling. (version 0.9.7)
I'm using arduino DUE and BLE Shield (redbearlab).
I get the error: EEPROM.h: No such file or directory in bootloader_setup...
I tried building ' pca10040 ' configuration of " nrf52-mpu-easydma-using-gpiote-and-registers " example from " https://github.com/Martinsbl/nrf5-mpu-examples ". The following...
Hi
I am working on nRF51-DK with Mbed IDE & used PWM example code from link : https://os.mbed.com/handbook/PwmOut
When enabled PwmOut, PWM signal is observed on the oscilloscope...
I would like advice on whether the following is a valid ble transaction.
We have a product with the nrf52 in it running sdk 12 and softdevice 3.0. This is setup as a a peripheral...
Hi,
I'm using nRF5 SDK v. 14.0.0. I'm trying to pass a context pointer to the NRF_SDH_BLE_OBSERVER macro, but am running into compilation errors. I want to do something...
Hi,
I'm building a project with nRF52832 dev kit and the SHT10 temperature and humidity sensor, I'm searching for a library/example project of this sensor and the nRF52...
I'm planning to make a custom board using Thing52, following the reference desing. I have some questions (1) Can I use nRF52840 instead of nRF52832? (2) Do you provide an...
To reduce power consumption during sleep I have to completely disable the UARTE0. This is done before sleeping by :
NRF_UARTE0->TASKS_STOPRX = 1; NRF_UARTE0->ENABLE = UARTE_ENABLE_ENABLE_Disabled...
We are using Bluetooth Developer Studio along with Nordic's code generator plugin (Nordic Semiconductor nRF5 1.3.0 SDK 14.0) for our project.
We've made a couple of improvements...
Hi!
I got an error while compiling the proxy client example in BLE Mesh SDK V 2.0.0 as The object file build/light_switch_proxy_client_nrf52832_xxAA_s132_6.0.0_Debug/obj...
HI al
I have a bicycle computer (A) host (SDK 12.1 51822QFAC S130-V2.0.1) and a slave device (B) for measuring bike speed and cadence (using 2032 batteries). 1. When the...
Hi, I was recently asking about OPUS - https://devzone.nordicsemi.com/f/nordic-q-a/32875/how-compile-opus/128181#128181 . Now I am able to run encode on audio data and decode...
Hi
We have a nrf51 dongle for use in a school prosject When the nrf51 dongle is connected to the USB slot in a computer it boots fine without holding the button when powering...
On the Getting Started page, I do not see the USB described in Step 7. I do not see any device. The LEDs flash and the buttons light up LEDs 1-4 as described.
Thanks
