Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I am creating a BLE beacon scanner, using nRF51822 and SDK 12.0.0. My beacons will be using public addresses so the upper 3-bytes of device addresses of all my devises will...
Hi,
in our application we will have a main MCU and a second MCU, an nrf52832.
We need to update the fwon the nfr52832 from the main MCU using a bootloader, via UART. ...
Hello,
I want to use 2 SPI bus with nRF52832 IC and SDK5. I can use the "SPI example" for first SPI bus. For the second SPI Bus, I think that I need to modify "sdk_config...
My devices require calibration and self test to be carried out after programming. To implement this, my device checks the JLink reset pin (configured as a GPIO on my NRF52...
Hi everyone, I'm trying to implement a simple bluetooth beacon which broadcasts / advertises the number of button presses and the time in seconds after the last button press...
Hi everyone,
I'm trying to change the advertisement data while advertising using an interrupt. So far I've managed to use a button to change the advertisement data.
...
Hi,
I have huge BLE carrier frequency drift, which cannot pass FCC requirement.
The drift is 256kHz which seems not normal.
I'm using 32MHz 10ppm xtal so drift should...
Hi!
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
In my application I am using Peer Manager to manage bonding and also...
Hi all
The errata sheet V1.8 states that the errata 143 applies also for the Bluetooth Low Energy mode. Does that mean that the BLE stack of the SoftDevice S132 is also...
Hi,
I am using nRF52832 DK and other same custom board, sdk v15.0 with SES IDE. My application like this:
For ble peripheral used example ble_app_uart and for central...
Hi Sir,
In my system (windows 7), I had install the GCC 4 .9 2015 q3 for SDK 14.2.0/12.3.0.
As reference the release note of SDK 15, the GCC upgrade to 6-2017-q2-update...
Good Morning Team, Hope your day is going well! Can you please provide the Full Material Disclosure (FMD) document for below part since I could not locate it on website. ...
Hi, I am merging the multilink example and the CDC ACM example in SDK15.
However, if you merge and run it, it will continue to fail.
Here is the source.
I have...
Hi, i am using a model based on simple_on_off model to send custom messages.
For now provisioner and client are separated as in the V2.0.1. I tried to combine them first...
Hi,
Is it OK to use the Nordic Semiconductor ASA (0x0059) ID for broadcasting data in the manufacturer specific data field?
If so is does Nordic provide a specification...
