I am getting a bt_hci_core: HCI driver open failed (-11) with a custom board using nrfConnect for VS Code and 2.9.1 toolchain/sdk.
The code is really simple (I'm not...
Hi,
I’m using the function lte_lc_psm_param_set(rptau, rat) . After connecting to LTE, I call lte_lc_psm_get(&psm_cfg.tau, &psm_cfg.active_time) and receive the following...
Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
Hello everyone. I'm creating a setup function to configure LSM9DS1 accelerometer and gyroscope by writing to the corresponding registers as shown below
Although this code...
I use sdk16.0 and nrf52832.
Can you give me an example of nrf52832 timeslot example ? thank you.
I read timeslot on DevZone,but many routines are missing files, resulting...
Writing an app for the Arduino Nano 33 BLE Sense:
https://store.arduino.cc/usa/nano-33-ble-sense
Basically I am reading all sensors on the Sense board (temperature, humidity...
I have programmed a Nordic Thingy 91 with lte_ble_gateway, and when I send command from the cloud to the device, an NRF_CLOUD_EVT_RX_DATA event is called, however evt->param...
Dear all,
I want to implement multiple functions with only one power button, including: 1. Power on/off, Long press to turn on, long press to turn off; 2. Functional response...
I am trying to connect nrf52840 dongle to multiple peripherals(nrf51822) ,so far i combined multilink_c example with uart_c and i can connect and read rssi value of only 1...
Sorry, my English is very bad.
I think I can only express my problem in Chinese.
在使用异步串口时，使用uart_rx_enable()设置的超时时间和真实发生UART_RX_RDY事件的时间相差巨大
using async serial port...
Hi,
We need to interface camera (0.3nrf52840MP to 2MP) with nrf52840 for a new product development. For evaluation purpose, is there any off the shelf camera module which...
I'm trying to add a timer to the usb_cdc_acm example to send a periodic text messages with the timer. I'm building on an Adafruit nRF52840 Feather Express board using Segger...
Hi ,
I am trying to parse the manufacturer specific data that a beacon is advertising.
I can read successfully the company_id but unable to read the "specific data " ...
Hello again Nordic Pro's,
As you probably all know by now, our product app is based on the subject example code, SDK and device. We need to programmatically disconnect from...
I have been trying ti debug with SES and re-installed everything trying to get it to work, for a while it did, but then it began showing this message:
also, it asks me...
Hi All,
I am working on nRF9160 GPS profile. built the code with Segger version 4.16 and updated the latest mfw_nrf9160_1.1.1 modem firmware.
when i compile try to catch...
Hello,
I am using nrf52840 and SDK 16.0.0
I have integrated two examples, ble_app_template and nrf_calendar example . Now I have a problem. I wanna update the manufacturer...
Hi
I just joined a development team for a monitoring system consisting of a master and 5 slaves. They have a prototype that works well, using the functionality of the ACK...
