Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I am trying to use SPI master + UART concurrently on the nRF52840 dongle. I am aware that the GPIO pins on the dongle can be used for SPI or UART. However, when trying to...
My nrf9160 which has the v1.0.0 modem and using v1.0.0 sdk has suddenly started continuouly resetting when i try to run asset tracker application. I have tried at-command...
Hello,
I am trying to build the lte_ble_gateway sample. I keep getting a JavaScript Alert TEST_RANDOM_GENERATOR.
I got something simalure with the bluetooth hci uart...
nRF52811 has only one receiver. Most accurate direction finding can be made based on estimation of phase difference between two signals received in two spaced antennas. Such...
Hello – My project needs to report its indoor position to the cloud (no GPS). I intend on using known positions of iBeacons SSID/RSSI coupled with trilateration math – fully...
Hi team, I developed own project based on /examples/dfu/secure_bootloader/pca10056e_ble/ses/. In the original project there was only Release config (no Debug). I modified...
I am trying to figure out how to configure my peripheral such that when a central client tires to enable the service changed characteristic that it succeeds. I am desperately...
I'm working on an application where I will need to initialize the modem, send/receive messages and then turn it down to low power until the next checkin. I did a real simple...
I have read that at each connection event master will send the first packet (empty payload).
In a case where slave latency > 1, the slave will not be listening to master...
Hi devs,
It is not a real issue it is about a possible misconception about app_timer
For my application, I am using multiples timers using app_timer_create. From my understanding...
So I'm coming to the nRF52832 from a couple decades worth of light occasional programming, mostly data analysis and scientific computing in nature, and primarily in C/C++...
Hello,
In my setup, I have 5 clients (buttons) that all report to the same server (lightbulb).
I'm using the Mesh SDK 3.2 light switch example with static provisioning...
Hi everyone, I successfully followed all the steps of the Getting Started Assistant on Windows 10 x64, but I am unable to open the Asset Tracker project because of some errors...
Hello, I was building the asset_tracker application in segger_embeded_studio v418 on Mac OS. I am using master branch( because we need real gps data), however, I encontered...
I know that master sents "LL_CHANNEL_MAP_REQ" to slave to indicate that there is a new channel map. I want to know does master keeps on doing channel sensing to know which...
